Rebuild 450hp machine

[Havok_KiD]

Hi Guys,

I am in the Mid of building my Evo 3 engine back...Need loads of advice on how to make this a success despite i have a lot of idea running in it

as what we know due to some lame excuses JPJ are not allowing us to register 63 block anymore i am doing a 67 conversion

what i have in mind is

4g67block
new pistons - 86mm
use current 67 rods
ACL bearings
fully balance the block
1.8mm metal gasket
272 cams
new turbo
700cc injectors
management

Now here is what i need.... i have a limited budget of 10k in hand

what brand/items shall i buy to make this a success as this is a DD car and as i said my aim is only 400 to 450whp
10k is excluding management as i have allocate funds for that seperately
not sure to use forged pistons, or DSM S256 or HX40 turbo

Sifu's your advice will be great here....

 

[bebolagalas T]

Hi Guys,

I am in the Mid of building my Evo 3 engine back...Need loads of advice on how to make this a success despite i have a lot of idea running in it

as what we know due to some lame excuses JPJ are not allowing us to register 63 block anymore i am doing a 67 conversion

what i have in mind is

4g67block
new pistons - 86mm
use current 67 rods
ACL bearings
fully balance the block
1.8mm metal gasket
272 cams
new turbo
700cc injectors
management

Now here is what i need.... i have a limited budget of 10k in hand

what brand/items shall i buy to make this a success as this is a DD car and as i said my aim is only 400 to 450whp
10k is excluding management as i have allocate funds for that seperately
not sure to use forged pistons, or DSM S256 or HX40 turbo

Sifu's your advice will be great here....

both turbo will suit ur target ..:proud: if want some thing diff than other go for HX40PRO..BUT S256DSM ETT already big enough!!

 

[Havok_KiD]

well bro...whats the cost for both....
innitial idea was to make my td05 to 20g with 360 thrust bearing...but then again...rather breath easily than chocking it

 

[ahmedshaikhani]

HX-40 is too big for your engine and HX-40 is efficient till 1.5Bar and after that it loses its efficiency. Go for GT series turbo GT30R will be an excellent choice for your car.

 

[bebolagalas T]

HX-40 is too big for your engine and HX-40 is efficient till 1.5Bar and after that it loses its efficiency. Go for GT series turbo GT30R will be an excellent choice for your car.

wow...:hmmmm: one of the highest pressure ratio in compressor map...faster spooling than gt35r...but you claimed it out of efficiency after 1.5 bar?

 

[Over Boost - Motorsports]

lose efficiency after 1.5 bar? i doubt that, im sure the 8 blade design able to push much more then the 6/7 blades design, right bebolas?

 

[kumar22mostwanted]

both turbo will suit ur target ..:proud: if want some thing diff than other go for HX40PRO..BUT S256DSM ETT already big enough!!

hello turbo sifu want to ask in comparison between the hx40pro 7 blade and the s256 ETT which one is more reponsive of course both being in a BEP DSM housing ???

 

[bebolagalas T]

lose efficiency after 1.5 bar? i doubt that, im sure the 8 blade design able to push much more then the 6/7 blades design, right bebolas?

Correct bro.. But the 40pro comes with 6/7blade design.. 3bar compressor map same like s256/9 Ett version..

 

[Havok_KiD]

walauwieh....hx40 only can go till 1.5bar...where u got such idea bro....hx40 can easily take 2 bar without even worrying .....its the most powerful turbo in industry which i am aware of beside bullseye or FP

 

[speed2horizon]

walauwieh....hx40 only can go till 1.5bar...where u got such idea bro....hx40 can easily take 2 bar without even worrying .....its the most powerful turbo in industry which i am aware of beside bullseye or FP

Well, if u gonna use banana, then no problem.. Just make sure u have sufficient supporting bracket to hold the heavy snail... If u gonna use OE cast iron manifold, then u need to think about the space in ur engine bay... sangkutz sini sangkutz sana...

 

[kumar22mostwanted]

Well, if u gonna use banana, then no problem.. Just make sure u have sufficient supporting bracket to hold the heavy snail... If u gonna use OE cast iron manifold, then u need to think about the space in ur engine bay... sangkutz sini sangkutz sana...

i think you only need to bend the water pipe other than that should be ok
but this was in an eclipse i saw on9
dont know how it will fit into proton

 

[bebolagalas T]

Well, if u gonna use banana, then no problem.. Just make sure u have sufficient supporting bracket to hold the heavy snail... If u gonna use OE cast iron manifold, then u need to think about the space in ur engine bay... sangkutz sini sangkutz sana...

Walauweh... U got lot of xperiece regarding fitting the turbo...hehe but kumar is right just a minor issue in water pipe if using bep housing.. Big issue if 3 layer radiator.. But dei where is my gasket bro???

 

[peterj]

Walauweh... U got lot of xperiece regarding fitting the turbo...hehe but kumar is right just a minor issue in water pipe if using bep housing.. Big issue if 3 layer radiator.. But dei where is my gasket bro???

of course, speed2horizon is another big sifu in ZTH kumar is another e3 engine modder thoughmonster dy

 

[kumar22mostwanted]

of course, speed2horizon is another big sifu in ZTH kumar is another e3 engine modder thoughmonster dy

S2H is the real sifu trust me ive met him
im just shitting out info from internet

 

[speed2horizon]

of course, speed2horizon is another big sifu in ZTH kumar is another e3 engine modder thoughmonster dy

S2H is the real sifu trust me ive met him
im just shitting out info from internet

U guys place me onda table... >.

Walauweh... U got lot of xperiece regarding fitting the turbo...hehe but kumar is right just a minor issue in water pipe if using bep housing.. Big issue if 3 layer radiator.. But dei where is my gasket bro???

already gave it to mr Magnusficent Jinkl bro... Abt 2months ago... Apa cer???

 

[jinkl]

lolx wuish , i already show firdaus the dsm gasket laaa

ahmedshaikhani : u got it wrong bro, HX40PRO will have a higer PR than the GT series anytime

bebolas : why does my 40pro have a oversized turbine wheel ? kekekekeke

 

[Havok_KiD]

lolx wuish , i already show firdaus the dsm gasket laaa

ahmedshaikhani : u got it wrong bro, HX40PRO will have a higer PR than the GT series anytime

bebolas : why does my 40pro have a oversized turbine wheel ? kekekekeke

hahaha JINKL its bcoz u onself ask for the big turbine wheel to fly to moon soon....dont worry i am joining your clan soon....HX40 team..wahaahahha
being greedy now

 

[bebolagalas T]

lolx wuish , i already show firdaus the dsm gasket laaa

ahmedshaikhani : u got it wrong bro, HX40PRO will have a higer PR than the GT series anytime

bebolas : why does my 40pro have a oversized turbine wheel ? kekekekeke

hahha..hx40pro with qtrim size turbine wheel for GREEDY dRagger who so HP FREAK!! MUAHAHA

---------- Post added at 01:40 PM ---------- 6 hour anti-bump limit - Previous post was at 01:37 PM ----------

U guys place me onda table... >.


already gave it to mr Magnusficent Jinkl bro... Abt 2months ago... Apa cer???

aper cer ape...sample ok la bro..quotation please!:hmmmm:

 

[Havok_KiD]

hahha..hx40pro with qtrim size turbine wheel for GREEDY dRagger who so HP FREAK!! MUAHAHA

hahahaha he JIN what..so much be able to run fast from us....hahaha....on the other hand...good combination of turbine wheel...can i do so :P