Please Advise Engine Changed

[tingwk]

Dear all Senior,

Good day to all of you,

Anyone can recommend me, which shop know how to exchange Wira engine to Mitsubishi engine very well.

I got one VR4 2.0 Turbo engine, thinking to find a workshop to do this engine changing......

Area in Petaling Jaya, Damansara.

Thanks for your kind info~ pls reply my post if u know~

 

[DanzEterna]

i can recommend u a good workshop, but its in pandan indah, ampang,
very good workmanship with reasonable pricing.
Intro AG Motorsport -

 

[tingwk]

i can recommend u a good workshop, but its in pandan indah, ampang,
very good workmanship with reasonable pricing.
Intro AG Motorsport -

Ala.....bro......very far for me go over there.....prefer PJ area if any.....anyway....thanks for your sharing

 

[DanzEterna]

icic, cos its my fren's workshop, can get cheaper there. cos i recommend.
how bout sunway area? got lotsa tuner workshops there.

 

[tingwk]

Sunway area there also very expensive...haha....or if u got friend there can get cheaper, then recommend me

 

[DanzEterna]

in sunway some expensive, some cheap.
u try calling up joe/DD05 he has his own shop in sunway, can give u lower price
compared to other places.
http://www.zerotohundred.com/newfor...906-cs-auto-evo-garage-service-promotion.html

 

[mazranz]

You can check out my friends place in section 20 pj. Jalan 20/7.

KF greenzone beside nationwide express and paramour garden restaurant.

Go talk to him. Easy going, good quality and price. Look for Keong.

He did my 300zx overhaul and engine swap. No problems so far!

 

[tingwk]

You can check out my friends place in section 20 pj. Jalan 20/7.

KF greenzone beside nationwide express and paramour garden restaurant.

Go talk to him. Easy going, good quality and price. Look for Keong.

He did my 300zx overhaul and engine swap. No problems so far!

Hye, bro, can i have his contact number pls....thanks a lot~

---------- Post added at 03:53 PM ---------- 6 hour anti-bump limit - Previous post was at 01:46 PM ----------

in sunway some expensive, some cheap.
u try calling up joe/DD05 he has his own shop in sunway, can give u lower price
compared to other places.
http://www.zerotohundred.com/newfor...906-cs-auto-evo-garage-service-promotion.html

Hye bro, joe asking me who is my friend, so may i know ur name pls?

 

[mazranz]

Hye, bro, can i have his contact number pls....thanks a lot~

---------- Post added at 03:53 PM ---------- 6 hour anti-bump limit - Previous post was at 01:46 PM ----------



Hye bro, joe asking me who is my friend, so may i know ur name pls?

My name is Mazran ;)

You can contact Keong at 012 338 3028

 

[DanzEterna]

Hye, bro, can i have his contact number pls....thanks a lot~

---------- Post added at 03:53 PM ---------- 6 hour anti-bump limit - Previous post was at 01:46 PM ----------



Hye bro, joe asking me who is my friend, so may i know ur name pls?

aiya, u tell him danz eterna lor...he know wan.......

 

[BE5RSK]

sori bro, little bit off topic question...

You are planning to put that VR4 engine into your Wira right?
Is there any new regulation by JPJ allowing proton chassis (except Perdana) to convert to 2.0 liter engine?

because all this while, i was told that there's no more 2.0 liter allowed in proton chassis (once again, except perdana)...:hmmmm:

 

[DanzEterna]

if wira 2.0 diesel should be able to as well.
not sure bout wira 1.8. but if according to 25% regulation should be able to.

 

[BE5RSK]

Danz, yeah that's right..
According to their written law, conversion of engine with not more than 25% from original engine displacement, no need to obtained kawalselia letter... if intend to put more 25% from original displacement, must obtained kawalselia letter/approval first. Plus, some runners mentioned that the engine mounting must no be altered or cut and welds.

The runners mentioned as well that even though Evo (1,2,3) engine goes into wira chassis is almost 100% plug and play and not required any alteration to engine mounting, but still wont get approval from JPJ because the wira chassis are not meant for evo engine power output..
in simple words, they said "itu wira body mana bole tahan sama itu evo punya power"...

Maybe someone could clarify this matter further?

 

[DanzEterna]

unless u send your car to proton factory to rebuild the whole front in order to get the perfect mounting to place 4G63T inside, also might need to double weld your chasis.

 

[tingwk]

Yeah....Both of u r right....only me playing the game without approval

By the way.....do u all know where can get the Engine mounting?

---------- Post added at 05:06 PM ---------- 6 hour anti-bump limit - Previous post was at 04:29 PM ----------

Dear All Big Brothers.....

Please help.....Where can i find the VR4 Engine Mounting? Urgent!! Got engine, but without Engine Mounting......If just use to cauterize with own customize Mounting....It is not safety, and not enough SOLID!....very easy to broke...So who knows where can i find it?

Please Advise ......Thanks a lot~~~

 

[BE5RSK]

Bro, VR4 engine mounting???

I would say, chop/halfcut shops are the best bet to get it.
If you want the brand new (which is I doubt the still produce it), you might try to visit PH Auto in Seapark PJ.
10 years ago, I managed to get ori OEM 4G61T engine mounting from them.

 

[tingwk]

Bro, VR4 engine mounting???

I would say, chop/halfcut shops are the best bet to get it.
If you want the brand new (which is I doubt the still produce it), you might try to visit PH Auto in Seapark PJ.
10 years ago, I managed to get ori OEM 4G61T engine mounting from them.

Thanks Bro, do u have the full address?? or any contact number??

 

[BE5RSK]

Here the address:

PH Auto Enterprise
No.7, Jalan 21/17,
Sea Park,
46300 Petaling Jaya,
Selangor.
Tel: +603-7877 2288 or +603-7877 1918
(GPS Coordinates: 3°6'33"N 101°37'21"E)

The shop is facing Maybank and shell petrol station.