26B@Quad Rotor Engine

[MooCP]

hi everyone.
i would like to know the price of the 26B at malaysia is how much and where can i buy it? anyone know? please feel free to tell =)

 

[b3_auto]

fuhyoh..... this one is really a speed demon lah.....

 

[MooCP]

Re: 26B @ Quad Rotor Engine [WTB]

yes i`m. haha. anyone anyone could answer?

 

[Lennon]

Get it from US..... but might not sell it to you, even you have $$$.... Estimated above RM25,000...

 

[jaii13]

Whoa Kean, long time no hear. What you been up to? Still have your 8?

 

[arsenalboi]

prob too expensive plus very high maintenance. why not a tried and tested 20b

 

[SomeGuy_sg]

Haha... You are a damn joker :P 26B
Let me tell you why i found your thread funny.
The R26B engine was a race only engine found in the Lemans car which mazda ran in late 80's or early 90's. It helped mazda be the first non American /European winner and the Only one that ever won without using piston engine . As after, the rtards at lemans banned the engine :P

If you want a 4-rotor engine, you better have robbed a bank. Custom is the only way to go. You can search up city performace or RE Kiwi . They have done it before.
let me lay it down for ya :D
Custom 4 rotor e-shaft - $15,000 RM
Custom center housing(2 needing for 4-rotor engine) - $1400RM x2
Dowel set for a 4-rotor - $300RM
Crank bearing set/kit - $3200 RM
And that is just the parts for the 4 Rotor kit you would still need to get 2 working 13B rotary engines and misc stuff like oil lines, stud set....

Well you get the idea. Yashiro Iron works in japan did one of the first few private 4 rotors. It was a gen 1 rx7 4 rotor carbed :P
If you do ever build it :) i call shotgun and dibs on the first ride out ;)

 

[SomeGuy_sg]

oops :)
ps; read this thread ghetto 4 rotor build - RX7Club.com

 

[phat7]

i actually m suprised somebody replied. the cheapest 26b is to superglue 2 units of 13b rew's. You get 4 turbos and voila 4 rotor special. Alchemis can custom make the driveline

 

[heavenz]

Put 1 13b engine in front to move the 2 front wheels and another 13b engine at the back to move the back 2 wheels. Now u have 26b with 4 wheels. No need cut firewall as well. Kakaka. Phat ur next project. 1 turbo for 1 wheel.

 

[phat7]

ghetto 4 rotor build - Page 6 - RX7Club.com

This guy is doing almost what i described but single turbo.nia mah!!

 

[MooCP]

alright. i will built a 26B now! xD

 

[RERider]

It is called "24A" based on 4 12A rotors and housings.Scoot in japan did it too.

 

[Lennon]

Whoa Kean, long time no hear. What you been up to? Still have your 8?

Yeah..... No replacement yet....

 

[zealless]

hi everyone.
i would like to know the price of the 26B at malaysia is how much and where can i buy it? anyone know? please feel free to tell =)

don't know about malaysia ... but scoot selling their 4 rotor engine in japan, roughly 150K ehehe, but price is 6 months ago ... good luck; enclosed email from scoot - [email protected]

Hello Mr,Kenny

thank you for e-mail

possible to sell 4 rotor engine.


When i make the 4rotor-car,
Our goal wanted to do finish the car like a factory maid.
We spend lot of money ^^;;

Spec: Power.500HP-600HP torque.45kg-60kg

cost of the engine
1)13B Based Engine +￥ 3,314,000 (Use Renesis parts)
(without Intake& exth Exhaust system)
2) Intake system ( 4Butterfly Throttle ) ￥483,000
3)Exhaust system(All system Cata+Rear end)￥714,000
4)ECU system & Ignissys(Power-FCx2&Wiring+ECU Fuel setting)￥472,500

The thing that becomes expensive is a difficult point because there are a lot
of special processings.

http://blog.gtroc.com/dino/cars/index.php
Prease open URL then scroll down..

sorry .I can not writing English well
Regards, Scoot-H,Koseki

 

[Lennon]

That's really wakes me up..... I would like see to who's gonna break the bank...