open pod air filter

[twistedichc]

tried house vacuum hose but it melts when accidentally touch hot metals. size of wash machine maybe not that big if size machine is 6kg & below

wifey lenovo wit tapatalk

---------- Post added at 10:44 PM ---------- 6 hour anti-bump limit - Previous post was at 10:43 PM ----------

tried house vacuum hose but it melts when accidentally touch hot metals. size of wash machine hose maybe not that big if size machine is 6kg & below

wifey lenovo wit tapatalk


wifey lenovo wit tapatalk

 

[stupidcar]

tried house vacuum hose but it melts when accidentally touch hot metals. size of wash machine maybe not that big if size machine is 6kg & below

wifey lenovo wit tapatalk

---------- Post added at 10:44 PM ---------- 6 hour anti-bump limit - Previous post was at 10:43 PM ----------

tried house vacuum hose but it melts when accidentally touch hot metals. size of wash machine hose maybe not that big if size machine is 6kg & below

wifey lenovo wit tapatalk


wifey lenovo wit tapatalk

Aw, that sucks. :\

 

[3309]

Bro, just bought the hose from accessory shop and DIY lah...I have done it to my car. it cost me RM50 for the hose only. The shop quote me RM150 including installation...save me RM100 already...he he

 

[synail]

share with u guys for preventing leaves, stone, bugs, kittens etc from entering our super cai

 

[stupidcar]

share with u guys for preventing leaves, stone, bugs, kittens etc from entering our super cai

Why not just do it with a clamp?

 

[synail]

I use what i got that time
feel free to upgrade

 

[vr2turbo]

well this is my diy

Looks like my water tank project piping......hahahahahaaha

---------- Post added at 02:43 PM ---------- 6 hour anti-bump limit - Previous post was at 02:41 PM ----------

Looks good and functional. Thought of using those old washing machine pipes.
Give it a good clean then nice.

Washing machine one too small. Can try cooker hood exhaust duct but may be too big....:hmmmm:

---------- Post added at 02:44 PM ---------- 6 hour anti-bump limit - Previous post was at 02:43 PM ----------

Why not just do it with a clamp?

In case of hot places use metal ones better

 

[mADmAN]

im looking for a 2.5" ID hose.... been going around hardware shops all oso dun have :(

dunno where else to hunt... need 2.5" ID so that i can fit it to my airduct

 

[twistedichc]

im looking for a 2.5" ID hose.... been going around hardware shops all oso dun have :(

dunno where else to hunt... need 2.5" ID so that i can fit it to my airduct

ID hose, is it pvc material, if yes can try those shop selling electrical accessories

wifey lenovo wit tapatalk

 

[mADmAN]

ID hose, is it pvc material, if yes can try those shop selling electrical accessories

wifey lenovo wit tapatalk

ID = Internal Diameter.

can be any material as long as its flexible enough and strong enough.

 

[twistedichc]

ID = Internal Diameter.

can be any material as long as its flexible enough and strong enough.

hhmmm that depends on degrees of the bends needed to be done coz those flex conduit is a bit stiff in bigger diameter. the ones I've ordered for my site was 2.5" but not sure wether internally @ externally but usually for electrical it's externally.

http://www.zerotohundred.com/newforums/attachment.php?attachmentid=517520&stc=1&d=1398678509

 

[stupidcar]

hhmmm that depends on degrees of the bends needed to be done coz those flex conduit is a bit stiff in bigger diameter. the ones I've ordered for my site was 2.5" but not sure wether internally @ externally but usually for electrical it's externally.

http://www.zerotohundred.com/newforums/attachment.php?attachmentid=517520&stc=1&d=1398678509

But intake hose aren't necessary needed to be hard right?
It isn't from the throttle body that part.
We are rerouting the intake, so a soft hose should be alright as well?

 

[mADmAN]

hhmmm that depends on degrees of the bends needed to be done coz those flex conduit is a bit stiff in bigger diameter. the ones I've ordered for my site was 2.5" but not sure wether internally @ externally but usually for electrical it's externally.

http://www.zerotohundred.com/newforums/attachment.php?attachmentid=517520&stc=1&d=1398678509

the one u posted might actually be alright... i dont need it to be super soft... but some bends is needed.. as i need to route it from the bumper over the wheel mudgeard and into the engine bay... similar to this area.

any idea where i can get the hose around pj/subang/shah alam/damansara?

i can always bring my airduct for a test fit..... btw... THIS is the airduct i have

 

[twistedichc]

y don't u use hose for the radiator, might got the size

wifey lenovo wit tapatalk

 

[mADmAN]

y don't u use hose for the radiator, might got the size

wifey lenovo wit tapatalk

not that flexible la radiator hose :(

 

[twistedichc]

that if edi use, still new might be bit soft, btw if u r interested, i can give my flex hose f.o.c but u need to come 2 ampang & give me the length u need

wifey lenovo wit tapatalk

 

[stupidcar]

Saw this at TTA ytd. Damnnnn not open pod but open drop in haahha.

https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-ash3/t1.0-9/10176054_717710794942277_1900850075808997114_n.jpg

 

[mADmAN]

that if edi use, still new might be bit soft, btw if u r interested, i can give my flex hose f.o.c but u need to come 2 ampang & give me the length u need

wifey lenovo wit tapatalk

i probably need about 2 meters only

thanks alot for the offer man! ill should be at ampanag point sometimes this week..... can PM me ur number?

 

[vr2turbo]

that if edi use, still new might be bit soft, btw if u r interested, i can give my flex hose f.o.c but u need to come 2 ampang & give me the length u need

Radiator hoses already have it's shape, cannot bend too much....

 

[twistedichc]

i probably need about 2 meters only

thanks alot for the offer man! ill should be at ampanag point sometimes this week..... can PM me ur number?

sorry bro double checked it's oni 2" max, but if still want it just give me a call

wifey lenovo wit tapatalk