I saw them in Enous before (1 utama). But it is closed for reno now. Maybe you can try the other Enous.here's a rough idea of how it should look like...
Google Image Result for http://www.himni-racing.com/images/Tial_44mm_inlet_outlet_clamps.jpg
I saw them in Enous before (1 utama). But it is closed for reno now. Maybe you can try the other Enous.here's a rough idea of how it should look like...
Google Image Result for http://www.himni-racing.com/images/Tial_44mm_inlet_outlet_clamps.jpg
Bro bore & stroke goes side by side, what u wanna achieve with ur engine is the ultimate goal. Low to mid power, or mid to high power ? If it's a drag racing engine then by all means mod it kaw kaw but dun think it's possible to be a decent daily driver anymore.yaa man..my decision to build up the 4g93t terbalik frm scratch def v confusing..tomo going to have to go library and read some more..nvm wait i fed up i chuck to my foreman..hehe..thanks bro
This is the terbalik version aka CM5A and CK series ? Or the older CD5A series ? I think u need computer management since ur mixing mivec and 4g93T tech, u could try askin a few sifu who manage to mix n match successfully, as far as i know if u use mivec ecu, how can it control the fuel ? Turbo need very good fuel control le too lean or too rich and u will have problems later. Most of the problems come if ur too lean tho, rich usually is ok.hello guys I'm planning to do 4G93T with Mivec head 4G92 DOHC. I will be using Wiseco Turbo Pistons 81.50MM 0.5MM oversized, Duratech Conrods, ACL Race bearings and turbo not decided as yet. What parts will be replaced in this conversion any idea ? I will be using 4G92 DOHC Mivec Head, 4G92 Mivec wiring, sensors and ecu. 4G93 Block, pistons, conrods, bearings and head gaskit of 4G93T most probably 2.0MM. What else will I be needing ? I have a confusion in my mind which water should I use ? 4G93 or 4G92 DOHC pump ?
Thank you sir for your kind reply. I am using CK4A as it is a Mitsubishi Lancer 2006 Model. I will be going for a standalone ecu for tuning[Fueling, Timing..etc]. But I need a good standalone ecu which has every function anti-lag, stepper motor, launch limiter, mivec controller etc. My aim is for drag no streeting. I have a GT30R lying with me but need to change its housing as it is too big any suggestions for housing ? One thing more can I start my car and run perfectly with stock ecu. The engine came up with Automatic transmission and I am gonna swap manual gear box. Is it just plug in manual gear box or do I need to play with wiring ? In mitsubishi do they have the same ecu for auto and manual transmission ?This is the terbalik version aka CM5A and CK series ? Or the older CD5A series ? I think u need computer management since ur mixing mivec and 4g93T tech, u could try askin a few sifu who manage to mix n match successfully, as far as i know if u use mivec ecu, how can it control the fuel ? Turbo need very good fuel control le too lean or too rich and u will have problems later. Most of the problems come if ur too lean tho, rich usually is ok.
Just wan to reconfirm, anyone encounter abit of engine whine ? Not the tepet sound it's abit like grinding sound. I change everything like bearing, belt, only cam gear didn't change. When idling can hear like grek grek grek den nothing den grek grek grek den nothing. I try to get the sound later once the car is in my hands now tidying up the interior and finishin sum touch up.
Anyone can share what item u guys use to stick into the ori bypass valve hole ? I found those rubber stopper from plumbing shop but my mech say it's too soft, scare it might not stand the heat and melt or get sucked into the turbo.
Stand alone will be better for your case, bout the turbo maybe u can try hybrid with evo 4 - 6.5 ? If the GT30R is a brandnew turbo then maybe u can try to customise manifold for it ? If u wanna change gearbox i believe it's pnp but depends on which gearbox u r using ? And ur speedometer might need to change if u want it to look neat I have seen people usin auto speedo with manual just ignore the 1,2,3,4,n,p thingy. Btw depends if ur goin for 4WD or 2WD ? Since u mention drag I suppose it will be a 4wd setup ? CK4A is mivec right ? It should be the engine ? 2006 u should be using CS body lancer i think ?Thank you sir for your kind reply. I am using CK4A as it is a Mitsubishi Lancer 2006 Model. I will be going for a standalone ecu for tuning[Fueling, Timing..etc]. But I need a good standalone ecu which has every function anti-lag, stepper motor, launch limiter, mivec controller etc. My aim is for drag no streeting. I have a GT30R lying with me but need to change its housing as it is too big any suggestions for housing ? One thing more can I start my car and run perfectly with stock ecu. The engine came up with Automatic transmission and I am gonna swap manual gear box. Is it just plug in manual gear box or do I need to play with wiring ? In mitsubishi do they have the same ecu for auto and manual transmission ?
I never compare side by side b4, but I assume it's diff coz one is from the E4-6.5 generation another is from E7-E9 gen ?hi wanna know 4g93 gsr n 4g93 gdi turbo manifold the same?
I assume it's the CM5A 4G93 GSR ? or is it the CD5A ? CD the timing belt is on right, CM and CS both the timing belt is on left.a 4G93 GSR manifold will NOT fit a 4G93GDI without modding tge location of the turbo, etc..I assume this is e CS5A
---------- Post added at 08:00 AM ---------- 6 hour anti-bump limit - Previous post was at 02:40 AM ----------
forgot to add..if u want the downpipe frm an airtrek turbo will fit
The ori 1.5 DOHC Triptonic I got gearbox problem b4, this is due to oil change not done properly, other friends with 4G93T triptonic never have major prob, most problem occur from bad oil or boost too much till gearbox can't withstand the power else everything is good without problem.hey guys.. does the auto gearbox for 4g93t last long? because i m thinking to get an used car with 4g93t auto...
thx for ur answer =p