TE71 Coupe Project Sharing

[toyotadriffter]

use back 7A flywheel. u can try porsche 944 timing belt

izzit posible to get the porsche 944 TB here in malaysia??? How much izzit roughly???

 

[EG9]

My mechanic get it for me, if you want I can ask my mechanic.

 

[EG9]

facing some problem with engine pigging. The problem will be high compression ratio on that engine. I think I'm running more then 13:1 CR which is very high. In order to solve the problem 1st try to increase max fuel pressure to 40psi, it's really help and engine pigging do reduce but it's still there in some certiam RPM.
Secondly, remap my ignition mapping to much lower ignition timing and increase the AFR by 8% in my Freedom ECU. Overall it run much smoother but the pigging is still there especialy on 5th gear and excelerate from 2K RPM to 3K RPM.

After a 360Km of running in, I try to remap the whole ignition map on the Freedom again. This time, the pigging is almost dissapear but due to lower ignition timing the car seem to respond a bit slower and lack of abit of torque compared to previously.

How good if we got high octane fuel. I can run higher ignition timing without worry on engine pigging.

anyway up to date, I haven't rev the engine pass 4k RPM.

 

[EG9]

Today test run adn drive to office. Can eliminate all the pigging during driving. But when I try to sudden push the trottle up to 60% open, the pigging is still there. Engine is getting smoother nad power is getting better.

Need to tune it up with wideband sensor after run in.

 

[netmatrix]

Hey Chu i saw you at about 10 in the morning in SB Industry area. Testing or what? hehehe.

 

[EG9]

Hey Chu i saw you at about 10 in the morning in SB Industry area. Testing or what? hehehe.

Went there for meeting with Distributor lar. Fetching my assistant with that car, she like wah....ur car if different from other ppl car hor, no carpet, suspension is hard, and she said it's look like initial D car....hahahahahahhaha. I just laugh only.

No choice lor, now have to run in that engine. Just drive that car to everywhere including office and my distributors office.

 

[EG9]

anyone got adjustable cam pulley?

 

[7Heaven]

bro chu u can try to contact david aka scomatic,
coz last week he asked me wan or not that stuff, and it is from AE92 1

 

[EG9]

He place deposit for the pulley from one of the forumer. Actually the cam pulley is the forumer fiend PUNYA friend.
End up untill now I still donno where is the pulley, have been contact here and there. They cam pulley not even in his hand, sell virtual pulley arr?

 

[7Heaven]

wah like that 1 ka?!!! this guys find something stupid and giler to do ah

 

[EG9]

As normal all the time like that. Last time whacked by honda guys in this forum also just because he wanna showoff but don't have knowledge on the particular car.

 

[7Heaven]

yea lo still remember that time lagi, that fucking idiot asking us to whack the honda guy, but he dint bring his car....
really sick!!!

 

[EG9]

yes yes.....dissapointed and pointness.
Just don't care and whack my car all out in Sepang that day.

 

[banzai]

hahahahah...LOL, i still remember tat embarassing thread.. super powerful virtual honda halfcut.. So now he also got virtual cam pulley ar??hahahha

So EG9, any luck on the real stuff?? OUG dun have ar?? or u went to melaka with ah choy...heheh

 

[7Heaven]

haha that's y he now not always reply or post in here oledi,

haha that thread really embarassed us la, all the honda guys also reply there, and fuck kao kao him till few 10 pages kakaka...
that day mr Banzai also he placed on table also....

 

[EG9]

hahahahah...LOL, i still remember tat embarassing thread.. super powerful virtual honda halfcut.. So now he also got virtual cam pulley ar??hahahha

So EG9, any luck on the real stuff?? OUG dun have ar?? or u went to melaka with ah choy...heheh

I didn't join the Bimmer convoy because my parent was here that day.

I've been calling 4 ppl for the same cam pulley, this fellow then follow the next one and the next one and the next one but the last fellow told me that the Toda adjustable cam pulley still in his customer car. damn!!!
I already check out the Redline motorsport adjustable cam pulley for 4AGE. The outlook is great and according to the boss that is the new design which utilised T6 alluminum.
I forget to ask whether it's 6061-T6 or 7075-T6 material.

I'm still hoping to get Toda adjustable cam pulley because the material is 7075-T6 with is the greatest among all alluminum material. But it doesn't look as fancy redline pulley.

 

[banzai]

nemind.. dun go for fancy..ur car ain't showroom bling bling car although specs and chassis wise u are far better than one....hahha

hmm.... why dun u order new set through amoil just like alvin did? not very ex also... shud in the region of hundreds too...... But then u have to wait for some time, probably 2 months??

 

[EG9]

hahahahah...LOL, i still remember tat embarassing thread.. super powerful virtual honda halfcut.. So now he also got virtual cam pulley ar??hahahha

So EG9, any luck on the real stuff?? OUG dun have ar?? or u went to melaka with ah choy...heheh

nemind.. dun go for fancy..ur car ain't showroom bling bling car although specs and chassis wise u are far better than one....hahha

hmm.... why dun u order new set through amoil just like alvin did? not very ex also... shud in the region of hundreds too...... But then u have to wait for some time, probably 2 months??

That fellow said will update the status tomorrow. No hard to wait. Just check it out 1st.

 

[EG9]

Just view the cam pulley. damn..It's not Toda. It's TODA.R. Donno what capalang brand.
Material is from steel not even alluminum.

Really wasting my time.

 

[hitz]

TODA.R ? Imitation??? Walau..