Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="zan" data-source="post: 1479615" data-attributes="member: 9632">1. Engine mounting needs to be replaced.2. Front absorber mounting is cracked and need replacement.3. Left arm need to be replaced.My questions are:i. Do I need to urgently replace my mountings or can it wait for a few months more? And if I do replace them, will I still be able to transplant another engine into my car using the new mountings?A : depends on when u will do an engine transplant. if soon, then leave it as it is. otherwise, just change the front and rear mountings which are reasonably cheap (between 30-50). excessive vibrations normally comes from these mountings which will tear due to wear. this of course can be corrected by increasing idel speed, but will affect FC though minimal.ii. Is it advisable to replace juz the front absorber or both front and rear? I'm currently using the stock absorber paired with APM lowered springs. If I do intend to change all four, what brand is reccomended and can they be paired with my current springs? Should I use oil, gas or gas+oil shocks?A: must change in pairs to ensure an even suspension performance as well as grip. either front pairs or rear pairs. for newly fitted absorbers and case of leak, its OK to change only the defective one. gas absorbers give harder ride but better control and roadhandling as the car dont bounce much. i would like to suggest u try Monroe Sensatrac as well as APM's version of it. of coz APM is a lot cheaper lah. Sensatrac gives good compromise on comfort and handling.iii. Is this serious?A: normal problem for suspension lower arm is torn bushings. u can just replace the bushings at a fraction of the cost. change the arm only if it is bent or dented.if u change the arm also, it will be recycled and sold as new. (replace bushing and respray new black paint - easy)</blockquote>

Verification

The Marketplace Latest

original rare spec Rays Volk Racing CE28 16x7jj...
- Started by david tao
- Chassis and Wheels
Honda CITY 1.5 E (A)
- Started by PIstonHeads
- Cars for sale
original BBS RE013 18x8jj offset +50 5H pcd 5x112...
- Started by david tao
- Chassis and Wheels
original rare Yokohama ADVAN Racing RG3 18x8 18x8.5...
- Started by david tao
- Chassis and Wheels
original Endless M4 S2 4pot 2pot brake caliper set...
- Started by david tao
- Chassis and Wheels
original rare Yokohama ADVAN Racing RG2 17x8.5jj...
- Started by david tao
- Chassis and Wheels
original rare WedsSport TC005 17x7jj offset +40 5H...
- Started by david tao
- Chassis and Wheels
Vifa Speakers Audison Amp
- Started by samuel118
- ICE -In Car Entertainment
original rare Yokohama ADVAN Racing RG3 18x8.5...
- Started by david tao
- Chassis and Wheels
Carbing R35 GTR GTR35 Brake Master Cylinder Stopper
- Started by aycy
- Engine and Performance

Posts refresh every 5 minutes

to install e manage ultimate or not

dear sifu,

i'm having a confusion at the moment, i'm driving ZC32S new swift sports, i have an existing EMU yet to install into my new car ...

i had some comment says that our stock ECU will relearn back to normal...

2010 Sepang 1000KM Race: 529KM's left and plenty of drama

https://www.zerotohundred.com/wp-content/uploads/2010/06/CMB_1108-600x398.jpg

More shots from in and around the pits and the pit straight. All car's have settled in according to their pace with slightly over 600km's...

Help plss.. just change ecu..

I just changed my Ford lynx 1.6 manual ecu.. and got a mazda ecu from chop shop.. what i noticed after changed the ecu.. timing a bit lariii.. sometime almost down to 0 ... and my car pickup also not so good... when...