Rm8k Wira & Jazz GK5 ownership experience-A long way to go

[KHNG940413]

Did you see my comment about the wobbly crank pulley? You should be able to visually inspect the pulley. Start the car and look at the pulley turn. If it wobbles then you potentially have your culprit.

China crank sensor - but was it made for your specific engine or a generic VDO sensor?

I have start the engine and inspect. Didn't have any wobble.
Yesterday I checked and try wobble the crank sensor itself at the bottom side and the car died same as the car usually went dead.

Not sure as I never see the package.

 

[parakey]

I checked and try wobble the crank sensor itself at the bottom side and the car died same as the car usually went dead.

From your picture, the whole thing looks pretty solid. How much force did you apply to wobble it?

 

[KHNG940413]

View attachment 578100

From your picture, the whole thing looks pretty solid. How much force did you apply to wobble it?

Use my hand and goyang like pusing your kopi while the milk is at the bottom. Hahahahhaha
Not very hard juz slightly goyang only

 

[parakey]

Use my hand and goyang like pusing your kopi while the milk is at the bottom. Hahahahhaha
Not very hard juz slightly goyang only

There's a reason why I asked. The sensor's position relative to the trigger wheel is supposed to be quite immovable. It cannot be "longgar" to the extent where a small force may deflect it. This will cause the sensor to miss a read and stall the engine.

Have you gotten a multimeter yet? Check to see if sensors are really faulty.

 

[KHNG940413]

There's a reason why I asked. The sensor's position relative to the trigger wheel is supposed to be quite immovable. It cannot be "longgar" to the extent where a small force may deflect it. This will cause the sensor to miss a read and stall the engine.

So what you mean is maybe my sensor is crooked is it?

 

[Izso]

So what you mean is maybe my sensor is crooked is it?

eh... you are not supposed to be able to shake the sensor bracket and all la wahlau... anyway it's beginning to sound more and more like sensor problem

 

[KHNG940413]

eh... you are not supposed to be able to shake the sensor bracket and all la wahlau... anyway it's beginning to sound more and more like sensor problem

I am not shaking the bracket sensor lah,hahahaha
I juz hold the sensor top wire tarik abit & goyang abit see will it make the engine dead.

Juz now I go to spare part shop and ask for Original Proton crank sensor is around RM190.
Haven't bought it yet since my car now still running ok....for now....hahahahahah

 

[Izso]

I am not shaking the bracket sensor lah,hahahaha
I juz hold the sensor top wire tarik abit & goyang abit see will it make the engine dead.

Juz now I go to spare part shop and ask for Original Proton crank sensor is around RM190.
Haven't bought it yet since my car now still running ok....for now....hahahahahah

You skimped for 190 bucks? Man oh man - chinese sensors are never good. Even those aftermarket meters using chinese sensors are rubbish.

 

[KHNG940413]

You skimped for 190 bucks? Man oh man - chinese sensors are never good. Even those aftermarket meters using chinese sensors are rubbish.

No lah, tomorrow only go and buy. Juz pass by and ask them 1st. Will update after installing the original
Sensor

 

[sweelt]

No lah, tomorrow only go and buy. Juz pass by and ask them 1st. Will update after installing the original
Sensor

good choice. Critical sensor better get ori.

 

[sanekit]

No lah, tomorrow only go and buy. Juz pass by and ask them 1st. Will update after installing the original
Sensor

maybe it it caused by the china OEM sensor. haha. coz if i remember correctly, VDO is a bit choosy with sensors.
and as @Izso and @parakey mentioned, the sensor supposed to be tight and snug at it's bracket/holder. it's not supposed to move even if u try moving it with your hands.

 

[KHNG940413]

Wira update

Juz now have bought the Crank sensor. And luckily my bottom engine cover also arrived yesterday. So later will install these 2 thing inside the car

 

[stupidcar]

Ok have u ever thought that your ECU is shit, try find one to swap and see if problem persists. or dismantle the ECU and see if the chips are still nice not leaking.

 

[minibeany]

maybe it it caused by the china OEM sensor. haha. coz if i remember correctly, VDO is a bit choosy with sensors.
and as @Izso and @parakey mentioned, the sensor supposed to be tight and snug at it's bracket/holder. it's not supposed to move even if u try moving it with your hands.

yeah... kena before... put in a OEM sensor... problem persist... When changed to original sensor problem solved

 

[parakey]

yeah... kena before... put in a OEM sensor... problem persist... When changed to original sensor problem solved

Which sensor was that? Was it installed by the mechanic or yourself?

 

[KHNG940413]

Wira update.

I had install both the crank sensor & the bottom cover. For now the car didn't went dead while idling,so i guess.....is ok?hahahahahahah

 

[parakey]

For now the car didn't went dead while idling,so i guess.....is ok?hahahahahahah

Good Luck

 

[KHNG940413]

Good Luck

Yup,really is good luck to me.
Hahahahahahaha

 

[sanekit]

Wira update.

I had install both the crank sensor & the bottom cover. For now the car didn't went dead while idling,so i guess.....is ok?hahahahahahah

ori sensors ah?

 

[KHNG940413]

ori sensors ah?

The packet say is made in malaysia & from Proton part centre soI guess..... Is ori? Hahahahahhaa