Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="JBQ" data-source="post: 1063904176" data-attributes="member: 55457">Quoted from <a href="http://72.52.145.132/renewable-energy/2242-water-sparkplug-73.html" target="_blank">Water Sparkplug - Page 73</a>The standard "Kettering" type ignition coil supplies 12-14v through the primary winding of the coil while the points are closed, this creates a strong magnetic field in the core of the coil, when the points open and current is abruptly removed from the primary winding, the field collapses and generates voltages in the region of 250v to 350v. It is the voltage of the collapsing field that is transformed in the secondary winding of the coil up to 100 times.Quoted from <a href="http://www.jetav8r.com/Vision/Ignition/CDI.html" target="_blank">http://www.jetav8r.com/Vision/Ignition/CDI.html</a>The coil is fed 12v to the primary winding. This in turn creates a large (enhanced by the iron rod) magnetic field which also surrounds the Secondary windings. The coil is now storing a large magnetic field (a Flux" field). When the +12v to the coil primary winding is turned off the magnetic ("flux") field inside the coil "collapses". This causes a "Back EMF" (Electro Motive Force) current in the primary wire of about 200-300volts. THIS IS IMPORTANT. Most think the coil converts 12v to 30,000 volts. Not exactly. See, this back EMF voltage of 300volts is now applied to both windings. When the coil collapses this rapidly changing magnetic field is also transferred to the "Secondary" windings as current (remember the discussion above about magnetism... "a changing magnetic field passing by a coil creates electric current").The Secondary winding is 100 times longer so produces a voltage about 100 times more than the Primary during collapse. Lets do the math. The Primary ("Low Tension") wire is about 300v during the Back EMF spike. So the Secondary ("High Tension") wire is 100 x 300=30,000 volts. This high voltage is going somewhere, somehow to ground. The faster the power cutoff is in the primary, the faster the collapse, and the faster (more powerful) that spark is. So, when the points open (instantly cutting off power to the coil) 30,000 volts goes to ground from the secondary winding via the spark plug....With the Kettering Induction ignition design, the coils are powered all the time at 12 volts and are commanded to collapse to spark by the ignition module. Here, the ignition module disconnects the primary winding coil ground. The coil secondary winding collapses to spark at about 30,000 volts. In the CDI design, the coils are not powered. They receive a short high (250 volt) pulse from the ignition module and then amplify that (100:1) to a much larger voltage spike (about 40,000 volts).</blockquote>

Verification

The Marketplace Latest

original rare Rays Volk Racing TE37SL Black Edition...
- Started by david tao
- Chassis and Wheels
Honda city JSracing gtwing spoiler
- Started by jeff6126
- Exterior and Body
Honda civic fd ~car spray(Ferrari red)
- Started by jeff6126
- Exterior and Body
Honda jazz fit gk flrs body kit
- Started by jeff6126
- Exterior and Body
BMW F10 ~M5 front skirt lip with glossy black
- Started by jeff6126
- Exterior and Body
Kia Forte gtwing spoiler
- Started by jeff6126
- Exterior and Body
BMW F30 M3 front skirt lip
- Started by jeff6126
- Exterior and Body
Proton Saga VVT Evo Front Bonnet Hood
- Started by jeff6126
- Exterior and Body
Perodua bezza gear up body kit/spoiler
- Started by jeff6126
- Exterior and Body
BMW F10 ~M5 front bumper set ~M5 kidney grille...
- Started by jeff6126
- Exterior and Body

Posts refresh every 5 minutes

Haltech 500 o2 control

Hi Guys,

just wanna know how does haltech sprint 500's o2 control works.

does it actually change the value on the base map permanently

or

just compensate the the settings on the base map leaving all the values...

anyone got r33 to sell?

im looking r33.. thax
pm me

DIY- Spray Rims - WHITE

did this DIY for my fren over the weekend...

items needed...
1.old newspaper
2.white spray 2 cans rm5 punya (better to use ACE white glossy finish spray)
3.clear spray 1 can (use 1 thin layer cos cudnt get white...