Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="kennethfong" data-source="post: 2321169" data-attributes="member: 4371">Yo ladies and gentlemen,I'm suffering from clutch slippage now, i need a clutch that can sustain up to 300 HP or even better 400 HP if there's any future mod with only 8.5 inch flywheel + pressure plate + clutch, mainly using my car for working trip and daily drive.... OK now i have few options, let me elaborate below for my solution:1) Get a single plate racing clutch, however i've just been released from hospital 6 weeks ago due to surgery on my left knee and i can't really press the hard clutch....price is around RM 1-1.5k which is affordable....2) Get a twin plate clutch, some branded ones like ACT or Exedy or HKS will do fine and not so hard to press, but the price is really expensive around RM 3-4K....3) Been informed that someone somewhere in this country can modify clutch, you'll just have to send them ur clutch, pressure plate and flywheel, they'll change and upgrade the clutch gripping area to a much powerful ones (dunno whether lorry or bus ones or not), and they'll modify the pressure plate too to suit the clutch they mod, also the flywheel is best we send them coz they might need to skim a lil bit coz the upgrade of clutch is just attaching a better gripping clutch which adds a few milimetre to the thickness.... and if u dun skim it, u dun have free play n can't change gear afterwards.... cost around RM 1-RM 1.5K and somemore can maintain lightweight clutch pressing which is good, the concept behind this is to extract the most help from the clutch plate and not the pressure plate itself, coz normally cheap single plate racing clutch depends on pressure plate to hold the clutch to the tightest strength in order to prevent slippage which makes it a heavy clutch.....4) change to original 9 inch flywheel, MMC 9 inch pressure plate, and 9 inch clutch.... should be able to withstand up to 300HP but still unknown how long it'll last.....cost is somewhere in between around RM 2k + 2.5k, for this i need to remachine a lil bit on the gearbox housing to clear 0.5inch of new flywheels and pressure plates and clutch.....sorry for the long post, so what is the best suggestion, i'm really headache now n i'm jus a poor guy.....</blockquote>

Verification

The Marketplace Latest

Mitsubishi Lancer Evo bodykit
- Started by jeff6126
- Exterior and Body
BMW F30 M3 front skirt lip
- Started by jeff6126
- Exterior and Body
Honda Civic FC fk7si front bumper set
- Started by jeff6126
- Exterior and Body
Mercedes Benz W213 E63 AMG Body Kit
- Started by jeff6126
- Exterior and Body
Honda Civic FD TypeR body kit
- Started by jeff6126
- Exterior and Body
BMW F30 M3 front bumper set
- Started by jeff6126
- Exterior and Body
Honda city gm6 front bonnet hood
- Started by jeff6126
- Exterior and Body
Honda Civic FC fk7si front bumper set
- Started by jeff6126
- Exterior and Body
BMW E60 M5 Front Bumper set
- Started by jeff6126
- Exterior and Body
original rare R-Pride Wado Sakura flower 15x5jj...
- Started by david tao
- Chassis and Wheels

Posts refresh every 5 minutes

Honda Freed S – For Urban Families (RM99,800 OTR)

Honda Malaysia Sdn Bhd has just introduced the new Freed S in Malaysia that boasts better affordability within the...

What are these meters for

Hey guys, i just want to know the specification on this meters listed below. just to have a sure confirmation.
what is a:
-vacuum meter
-water temp
-oil temp
-oil pressure
-fuel pressure
-air fuel ratio
-exhaust temp...

evo 7&8 under carriage cover rm250

evo 7 or 8 under carriage cover, rm250... pm me if interested...http://i208.photobucket.com/albums/bb106/LE20V/DSC09998.jpg