Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="shiroitenshi" data-source="post: 3208942" data-attributes="member: 27518">sfl, user friendly wise, I think the simpler is easier, but it is limited in functions.As for VAFC, I don't mind it at all, but it's limited in the sense of how much correction it can put out without affecting ignition timing, sure, it can correct fuelling at low and part throttle, but its just really a MAP sensor manipulator, so it doesn't control ignition and fuelling directly. Really good for stock engine with light intake/exhaust mods, usually because when you modify honda exhaust system, the lower end will be rich, and the higher end will be lean, so the VAFC can correct that to a certain extent.but other than that, I find them really lacking when using on non-stock engines because VAFC relies on the stock mapping of the ECU.I haven't played with the MSD 6AL, so I don't know how flexible the ignition timing can be.But B20B setups work really well only with standalones, because the stock ECU mapping just isnt good enough, even with minor corrections. With anything less like a piggyback, you can achieve good peak hp, but the mid range horsepower (the horsepower reading at 2-6K rpm will not be as good)Injector control with standalones is also better. Even with 345cc H22A injectors, it's possible to make a B16/18C/B20B idle like a stock car. (not to mention faster to tune)I'm not sure how your mechanic will manage with just VAFC because the honda ECU has ignition and fuelling comprensation/correction, and without running open loop, it's like tuning a fuel ratio that's never constant due to temperature changes. Tune today, get 14.7AFR, start up tommorow, it becomes 12.3 or some other number.Most people don't know that for adjusting ignition timing, the 2 pin diagnostic/service connector needs to be shorted to disable compensation when adjusting ignition timing at idle. That's why when you get a timing light and test the timing for most cars, it won't be 16, or about 22 degs (with compensation)but get the service connecter jumpered, time it at 16 degs, and no matter how many stock P30 B-series you do the same to, when jumpered, it will always read 16.Now you know why some mechs adjust the ignition timing so many times, even though you only actually have to do it once... after swapping the belt, or removing the crank pulley for oil pump/etc service.</blockquote>

Verification

The Marketplace Latest

original rare Enkei ES Tarmac 15x7jj offset +35 4H...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing SE37 17x7.5jj offset...
- Started by david tao
- Chassis and Wheels
original rare Yokohama ADVAN Racing TC4 18x8.5...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing ZE40 17x9jj offset...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing INGS TS06 18x8jj...
- Started by david tao
- Chassis and Wheels
New original Defi Advance A1 NA package triple...
- Started by david tao
- Engine and Performance
original rare Rays Volk Racing CE28 16x7jj offset...
- Started by david tao
- Chassis and Wheels
Honda Jazz/Fit JSracing GTwing Spoiler
- Started by jeff6126
- Exterior and Body
Toyota Vios NCP93 front bonnet hood
- Started by jeff6126
- Exterior and Body
Honda civic fc varis spoiler
- Started by jeff6126
- Exterior and Body

Posts refresh every 5 minutes

Mr2>>>>lambo.....

Just wanto share something with u all's........enjoy it.....

http://sooyeshun.blogspot.com/2009/04/lamborghini.html

Nissan GT-R Confirmed Production

Nissan GT-R Confirmed Production

As i said earlier in the Nissan GT-R Complete information thread, the new Nissan GT-R is not a Skyline anymore, its an individually tagged GT-R.

Despite its expected price tag of...

rx7 savana 1982 model 4 sale..pic in

1 owner,
white colour,interior cantik,
17" volks rim,
fc 13b turbo engine,
r.tax hidup lagi,
tip-top cond,
spoiler,
meters,
rm14k...neg...
0162744036...