Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="jswong" data-source="post: 1063454145" data-attributes="member: 8004">My personal experience with UR bars in my old Wira - 3 point fender bars, 4-point front strut bar, room bar, and rear 3-point bar - These bars worked as advertised in numerous ways. My suspension setup is just a combination of Sapura springs and APM Performax shock absorbers, so the car wasn't lowered by much and it's still comfortable when driven over bumps. During hard cornering and all, the car feels more planted with the bars on than they were before I installed the bars. And that's when I'm driving with 205/45R16 tyres. It's still comfortable when I drive over road undulations, probably because I don't have those hard-as-a-rock short stroke or adjustable suspension kits.There was a time when my car was hit by another car that flew out of a junction while I was on the main road and had right-of-way. The driver was SMSing and didn't pay attention to driving. The front end of my car got struck at an angle, and due to the speed, the car continued smashing up the rest of the front end of my car, resulting in the destruction of my entire front bumper, the radiator, headlamps, bonnet, etc. The front panel was totally smashed that the body shop had to knock it out and weld a replacement front panel assembly (the front section to which the headlamps, radiator, etc. are mounted). To the bodyshop's surprise, they expected the front bulkheads to require pulling, since the car struck the front half of my left fender. But after removing the damaged wheel and the fender panel, they discovered that the bulkhead only needed knocking to straighten out the dent on its front end, and the chassis alignment for my whole front end was intact. The surprised bodyshop mechanic attributed the lack of chassis distortion to the 3-point fender bars and the 4-point strut bars that had vastly improved the strength of my car's front end. He said that usually in such cases, they would be putting those hooks and chains at the bulk head and straightening them out, but in my case, it's all just knocking and panel-beating.</blockquote>

Verification

The Marketplace Latest

New original Defi Advance A1 NA package triple...
- Started by david tao
- Engine and Performance
original rare Rays Volk Racing CE28 16x7jj offset...
- Started by david tao
- Chassis and Wheels
Honda Jazz/Fit JSracing GTwing Spoiler
- Started by jeff6126
- Exterior and Body
Toyota Vios NCP93 front bonnet hood
- Started by jeff6126
- Exterior and Body
Honda civic fc varis spoiler
- Started by jeff6126
- Exterior and Body
BMW F10 Msport front bumper set
- Started by jeff6126
- Exterior and Body
BMW F30 M3/GTS front bonnet hood
- Started by jeff6126
- Exterior and Body
BMW F10 vorsteiner rear bumper diffuser
- Started by jeff6126
- Exterior and Body
Mitsubishi Lancer Evo bodykit
- Started by jeff6126
- Exterior and Body
BMW F30 M3 front skirt lip
- Started by jeff6126
- Exterior and Body

Posts refresh every 5 minutes

Proton Preve website is up!!

Screen-Shot-2012-04-06-at-9.15.19-PM-600x308.jpg

The official website is up! You won't be able to see the name to click on but you can swap the...

Does ck 4g93t (terbalik) share some parts frm the older 4g93t?

Can ck 4g93t(terbalik) use aftermarket piston/conrod/bearing meant 4 the older 4g93t?

Greetings everyone, i've got some noob questions here..

1: Can the ck gsr(terbalik) use the wiseco pistons+duratech...

Spray colour code?

how to find the perfect match spray colour for my car?...mine is the new se colour... the dandelion yellow...