if you are looking for daily use...and just for the pick on the traffic light..
this seeting shuold be nice....
1)4-2-1 extrator (if you are original Wira SE it come with good Mendrel bent extrator been improve and dyno proven from my friend car Low rpm to mid power)
if you wan to use 4-1 extrator is not recomend due to respond start at 3k rpm above you need to high rev it....Sohc engine does not build for high rev..is build for low rev only...
2) get a 1.6 clutch set with lighten flywheel (normally people will lighten is to same wegiht of 1.5 clutch set...but then have to lighten more again..for lither then 1.5 clutch set.
3) lighten crank pulley install for siemens car.
4) get your car for port and polish and skim the head not more then 1mm for daily use...if not you will face overheating problem.
5) wira Se original piping is 1.75" mendrel bent and very smooth air flow good enuff and yet mendrel bent piping ain cheap..also it produce good power...
if your car doen not comes with mendrel bent...get yourself a 2" piping internal should be 1.78 or 1.8" depend on the thickness of the piping.
6) do not use OPen pod for siemens wira 1.5 you will face loosing torque .... stick back the box use K&N , UTR or others high performance high flow filter.
7) Cam degree...get 262,265 or 268....this is from MAtspeed for siemens car..do not go over 27x degree...you will facing idle problem which can`t solve in siemens ecu..
8)spark plug, you can use CAmpro engine spark plug is smooth enuff ..no need get those irridium...those actually for longer life span.. honest speaking..
9) suspension got many type..if normal daily use not racing or anything..get a ready make sport spring and must goes with sport absorber....
any infor need to add? you guy can add..hahaha
this seeting shuold be nice....
1)4-2-1 extrator (if you are original Wira SE it come with good Mendrel bent extrator been improve and dyno proven from my friend car Low rpm to mid power)
if you wan to use 4-1 extrator is not recomend due to respond start at 3k rpm above you need to high rev it....Sohc engine does not build for high rev..is build for low rev only...
2) get a 1.6 clutch set with lighten flywheel (normally people will lighten is to same wegiht of 1.5 clutch set...but then have to lighten more again..for lither then 1.5 clutch set.
3) lighten crank pulley install for siemens car.
4) get your car for port and polish and skim the head not more then 1mm for daily use...if not you will face overheating problem.
5) wira Se original piping is 1.75" mendrel bent and very smooth air flow good enuff and yet mendrel bent piping ain cheap..also it produce good power...
if your car doen not comes with mendrel bent...get yourself a 2" piping internal should be 1.78 or 1.8" depend on the thickness of the piping.
6) do not use OPen pod for siemens wira 1.5 you will face loosing torque .... stick back the box use K&N , UTR or others high performance high flow filter.
7) Cam degree...get 262,265 or 268....this is from MAtspeed for siemens car..do not go over 27x degree...you will facing idle problem which can`t solve in siemens ecu..
8)spark plug, you can use CAmpro engine spark plug is smooth enuff ..no need get those irridium...those actually for longer life span.. honest speaking..
9) suspension got many type..if normal daily use not racing or anything..get a ready make sport spring and must goes with sport absorber....
any infor need to add? you guy can add..hahaha