Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="Tohsan" data-source="post: 2131134" data-attributes="member: 6705">The MacPherson strut is a type of car suspension system widely used in modern vehicles, named after Earl S. MacPherson who developed the design. The first car to feature MacPherson struts was the 1949 Ford Vedette,[1] and it was also adopted in the 1951 Ford Consul and later Zephyr. It can be used for both front and rear suspensions, but is usually found at the front, where it provides a steering pivot (kingpin) as well as a suspension mounting for the wheel. Rear struts of a similar design are properly called Chapman struts.It consists of a wishbone (A-arm) or a substantial compression link stabilized by a secondary link which provides a bottom mounting point for the hub or axle of the wheel. This lower arm system provides both lateral and longitudinal location of the wheel. The upper part of the hub is rigidly fixed to the inner part of the strut proper, the outer part of which extends upwards directly to a mounting in the body shell of the vehicle. This type of suspension is only used with monocoque (unitary) body construction since the upper mounting can be a reinforced portion of the inner wheel well. The strut will usually carry both the coil spring on which the body is suspended and the shock absorber, which is usually in the form of a cartridge mounted within the strut. The strut also usually has a steering arm built into the lower inner portion. The whole assembly is very simple and can be preassembled into a unit; also by eliminating the upper control arm, it allows for more width in the engine bay, which is useful for smaller cars, particularly with transverse oriented engines such as most front wheel drive vehicles have. For those reasons, it has become almost ubiquitous with low cost manufacturers.Although it is a popular choice due to its simplicity and low manufacturing cost, the design has a few slight disdavantages, with regards to the quality of ride it provides and how it affects the handling of the car. Geometric analysis shows that it cannot allow vertical movement of the wheel without some degree of either camber angle change, sideways movement, or both. It is not generally considered to give as good handling as double wishbone suspensions, because it allows the engineers less freedom to choose camber change and roll center. The wheel tends to lean with the body, leading to understeer. Another drawback is that it tends to transmit noise and vibration from the road directly into the body shell, giving higher noise levels and a "harsh" feeling to the ride compared with systems such as double wishbones, requiring manufacturers to add extra noise reduction or cancellation and isolation mechanisms. Also, because of its greater size and robustness and greater degree of attachment to the vehicle structure, when the internal seals of the shock absorber portion wear out replacement is relatively expensive compared to replacing a simple shock absorber. However, despite the stated drawbacks the strut setup is still used on high performance cars such as the Ford Mustang, Porsche 911, all BMWs except the 2007 X5 [2] and several Mercedes-Benz models.</blockquote>

Verification

The Marketplace Latest

Proton Preve R3 body kit
- Started by jeff6126
- Exterior and Body
Perodua Ativa gear up body kit
- Started by jeff6126
- Exterior and Body
BMW F10 Mperformance front skirt lip
- Started by jeff6126
- Exterior and Body
Honda Civic FC fk7si front bumper set
- Started by jeff6126
- Exterior and Body
brake caliper spray
- Started by jeff6126
- Exterior and Body
BMW F30 M3 bodykit/diffuser set
- Started by jeff6126
- Exterior and Body
Perodua Axia Rahmah bodykit
- Started by jeff6126
- Exterior and Body
Nissan Almera Tomei body kit
- Started by jeff6126
- Exterior and Body
original rare Black Racing Pro N1 16x6.5jj offset...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing TE37SL Black Edition...
- Started by david tao
- Chassis and Wheels

Posts refresh every 5 minutes

Humble DIY Repairs On My Car

First DIY video to diagnose a Check Engine Light with accuracy. More DIY videos to come on this channel “Forged For Speed”. Stay tuned.

...

Lego Porsche 911 Cabriolet with working PDK blows mind w/video

https://www.zerotohundred.com/wp-content/uploads/2011/07/lego-600x371.jpg

Lego is awesome, it doesn’t matter if you’re five or 50 years old, joining the little bricks together to bring something in the depths of...

fs: varis rear boot

rm 2900 new

e789
call 012 2083222