Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="Izso" data-source="post: 1064585447" data-attributes="member: 2429">Wheelspin = get LSD. About 1k price range for used. Driveshaft - custom driveshaft or modified one probably 1k price range. Gearbox - don't modify over the capacity of the GB. Close story.VDO is smart enough to handle you in your current financial situation. Once you start venturing into forced induction then it'll be time to consider piggybacks or standalones.Wiser in what sense? There are pros and cons to both scenarios. If transplant, need to consider refurbishing the 4G93T. Engine alone approximately 4k, refurbish and all, probably 1.5k, then installation 1k, JPJ - time and finally puspakom - 100+ and must adhere to all puspakom guidelines otherwise you'll waste a lot of time redoing the inspection.BOT the 4G15 you don't need to do any registration and you'd be familiar with whats good and whats bad about the engine. It's also much easier to work on compared to DOHC. Lesser parts to fail and easier to tune. Personally I'd go with 4G15 and mod that. Cost wise probably will be less cost effective but nothing beats the satisfaction of building your own car rather than borrowing it from another engine that's not yours to begin with. Maybe it's just me and my 6 months DIY overhauling the engine which makes me so sentimental to 4G15 engines.NA will always give the more immediate performance gains but FI will give you the bigger kick in the balls but is more of a handful. NA is less likely to get you in trouble with JPJ roadblocks and NA is helluva easier to mod compared to FI. And the thing is - with NA, you can anytime opt to go FI. Sort of. That's assuming you don't go high compression like I did.</blockquote>

Verification

The Marketplace Latest

MITSUBISHI / FE658 (RB/BK S2S)
- Started by PIstonHeads
- Chassis and Wheels
Perodua Alza gear up body kit
- Started by jeff6126
- Exterior and Body
brake caliper spray
- Started by jeff6126
- Exterior and Body
Honda city Mugen gtwing spoiler
- Started by jeff6126
- Exterior and Body
Honda Civic FD JSracing GTwing spoiler
- Started by jeff6126
- Exterior and Body
Honda civic FC varis GTwing spoiler
- Started by jeff6126
- Exterior and Body
JSracing GTwing spoiler
- Started by jeff6126
- Exterior and Body
Proton saga drive68 bodykit
- Started by jeff6126
- Exterior and Body
Perodua Bezza projectR body kit
- Started by jeff6126
- Exterior and Body
Honda city gm6 drive68 body kit
- Started by jeff6126
- Exterior and Body

Posts refresh every 5 minutes

Meter cluster problem

Anyone can shade some light to my issue..i remove all the dashboard due to some mice stay somewhere in dashboard,after i reinstall back,meter cluster not fully works,light is on,the needle moves,but the kmh digital...

Evo 8 Meter Cluster Bulbs

Does anyone where am I able to get those Speedometer bulbs for Evo 8? prefebly led ones. Mine's almost all gone :hmmmm:

Check Light after Emanage Installation

Hi all,

I'm currently on a CE9A (Evo 3) running stock setup except 2.5" downpipe and 3" piping behind, an open pod and avcr running max 1 bar.

Everything is fine.

Just installed Emanage (Blue) with full harness...

Search

Enjoying Zerotohundred?

Log-in for an ad-less experience

Reply to thread

The Marketplace Latest

MITSUBISHI / FE658 (RB/BK S2S)

Perodua Alza gear up body kit

brake caliper spray

Honda city Mugen gtwing spoiler

Honda Civic FD JSracing GTwing spoiler

Honda civic FC varis GTwing spoiler

JSracing GTwing spoiler

Proton saga drive68 bodykit

Perodua Bezza projectR body kit

Honda city gm6 drive68 body kit

Posts refresh every 5 minutes

Recent Posts

Recommendation: Turbocharger for 4B11 N.A engine

2026 Vios HEV launched with Local Battery Assembly - UMW Toyota Motor

SPPF: The Future of Automotive Surface Protection - A Technical Overview

Upping Wira 1.5 MMC performance

Volvo Malaysia Launches Locally Assembled ES90 Electric Sedan

Search

Online now

Enjoying Zerotohundred?