Microtech

vteckiller

Supporting Merchants
Senior Member
Thread starter
Nov 17, 2003
1,606
34
3,148
easy answer:rofl:
ya la no need head ache...
already said can but say cannot then no need other advise d la..
buy new one ler..

i did b4 so i know...but nvm..best buy new one...
:biggrin:
 

kimloong_8

Known Member
Senior Member
Mar 13, 2009
188
0
1,516
Who have mircotech LT10-s wiring diagram use in Honda H22a!!!

Bump: Who have mircotech LT10-s wiring diagram use in Honda H22a!!!
 

3rd GearPerformance House

500 RPM
Senior Member
Nov 5, 2008
625
4
1,518
check the web microtecefi.com for wiring diagram.if u have more credit call Jon for ask a question.

Bump: check the web microtecefi.com for wiring diagram.if u have more credit call Jon for ask a question.
 

vteckiller

Supporting Merchants
Senior Member
Thread starter
Nov 17, 2003
1,606
34
3,148
h22a and b16a and b18c all same wiring..if ek b16b only obd2 different wiring..

Bump: h22a and b16a and b18c all same wiring..if ek b16b only obd2 different wiring..
 

kimloong_8

Known Member
Senior Member
Mar 13, 2009
188
0
1,516
Teh Microtech LT10-s have Gnd at beside the crank input 1 and also the Power M/C beside the crank input 2 is use for what? Where I can get the ignition input drawing diagram?

Bump: Teh Microtech LT10-s have Gnd at beside the crank input 1 and also the Power M/C beside the crank input 2 is use for what? Where I can get the ignition input drawing diagram?
 

vteckiller

Supporting Merchants
Senior Member
Thread starter
Nov 17, 2003
1,606
34
3,148
Teh Microtech LT10-s have Gnd at beside the crank input 1 and also the Power M/C beside the crank input 2 is use for what? Where I can get the ignition input drawing diagram?

Bump: Teh Microtech LT10-s have Gnd at beside the crank input 1 and also the Power M/C beside the crank input 2 is use for what? Where I can get the ignition input drawing diagram?
hope this will help u out..its lt8 but the crank sensor wiring is 100% the same..
http://www.microtechefi.com/pdf/LT8HONDAVTEC16Toothanti-clock.pdf

Bump:
Teh Microtech LT10-s have Gnd at beside the crank input 1 and also the Power M/C beside the crank input 2 is use for what? Where I can get the ignition input drawing diagram?

Bump: Teh Microtech LT10-s have Gnd at beside the crank input 1 and also the Power M/C beside the crank input 2 is use for what? Where I can get the ignition input drawing diagram?
http://www.microtechefi.com/pdf/LT8HONDAVTEC16Toothanti-clock.pdf
try this la..
the lt10s and lt8 shares the same cranksensor wiring
 
May 19, 2009
3
0
1,501
:confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?

Bump: :confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?

Bump: :confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?
 

vteckiller

Supporting Merchants
Senior Member
Thread starter
Nov 17, 2003
1,606
34
3,148
:confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?

Bump: :confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?

Bump: :confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?
y your friend so poor thing one..
could be due to many factors...poor rebore or timing not right or fuel pump presure not constannt..

since u scared better u install afc la..:biggrin:
 

3rd GearPerformance House

500 RPM
Senior Member
Nov 5, 2008
625
4
1,518
U cant say the ECU is a problem,over 100pc of ecu im install with stock engine,never facing any problem.But some time have a problem with the other engine rebuilder.For me when tuning for daily driving we make a economic fuel comsuption.For boost and performance depent on your engine set up.For stock Mivec 1.6 we make 165whp and good torque.Pls beware with a Non Authority Microtech tuner.
:confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?

Bump: :confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?

Bump: :confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?
Bump: U cant say the ECU is a problem,over 100pc of ecu im install with stock engine,never facing any problem.But some time have a problem with the other engine rebuilder.For me when tuning for daily driving we make a economic fuel comsuption.For boost and performance depent on your engine set up.For stock Mivec 1.6 we make 165whp and good torque.Pls beware with a Non Authority Microtech tuner.
:confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?

Bump: :confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?

Bump: :confused: best,good,performance for microtch,that wht i know.... i want try 4 my wira mivec but stil afraid about wht happen 2 my friend, 1 week after instll, engine get overhl, piston ring jam, oil engine smell petrol, full tank petrol can use about 200km..... explain bro.tq:confused::confused:?
 
May 19, 2009
3
0
1,501
:driver: thanks bro!!! maybe

(Pls beware with a Non Authority Microtech tuner.) my prend say, 'tuner' at industrial area in subang... jz beware maybe....:wavey:

Bump: :driver: thanks bro!!! maybe

(Pls beware with a Non Authority Microtech tuner.) my prend say, 'tuner' at industrial area in subang... jz beware maybe....:wavey:
 

3rd GearPerformance House

500 RPM
Senior Member
Nov 5, 2008
625
4
1,518
Yah good for u and your frends..:biggrin::biggrin::biggrin:
:driver: thanks bro!!! maybe

(Pls beware with a Non Authority Microtech tuner.) my prend say, 'tuner' at industrial area in subang... jz beware maybe....:wavey:

Bump: :driver: thanks bro!!! maybe

(Pls beware with a Non Authority Microtech tuner.) my prend say, 'tuner' at industrial area in subang... jz beware maybe....:wavey:
 

vteckiller

Supporting Merchants
Senior Member
Thread starter
Nov 17, 2003
1,606
34
3,148
i wonder who he is refering too? in subang industrial ?
:idea:
 

3rd GearPerformance House

500 RPM
Senior Member
Nov 5, 2008
625
4
1,518
Better go to Mellinium la bro...he expert person about mikotek la bro.Have a good dyno facility there.:rofl::rofl::rofl:

Bump: Better go to Mellinium la bro...he expert person about mikotek la bro.Have a good dyno facility there.:rofl::rofl::rofl:
 

kimloong_8

Known Member
Senior Member
Mar 13, 2009
188
0
1,516
How I can change the Input Trig and Out Put Trig? I cann't find in the Microtech LT10 inside the setup screen!!!! My only can see Teeth CAS and TDCref CAS. How I know the microtech ECU for the car model? Thank
 
Last edited:

Random Post Every 5 Minutes

Hi, im changing a metal gasket should i skim the engine head and block with a thin layer ??

---------- Post added at 06:00 PM ---------- 6 hour anti-bump limit - Previous post was at 05:27 PM ----------

Bump, help plsss.
Ask a question, start a discussion or post something for sale!
Post thread

Online now

Enjoying Zerotohundred?

Log-in for an ad-less experience