4G91 Gang..

[afatt]

how much cost to change valve lifter? some frenn call hydrolic tensioner, its rite?

 

[calvin9683]

mediocre2....
i think u should "korek" more info from bro joe_mirage....
since u r running high cams now.... if u dun increase ur rev limit, mayb u wont get the MAX output... pester joe_mirage... let him spill the beans....
as for ur exhaust.... dont u think 2 bullet there is killing all the horses??? take out another bullet... n continue running on straight pipe... sure damn shiok!!! last time i was using "throttle body" at my exhaust... oni 1 bullet before the "opening".... when open the throttle body.... damn lots of diff lo.... see block close it... no issues.... heehee

bro ACQ... emanage for RM300??? how izzit possible???

 

[mediocre2]

Calvin,
Hmmm yea Wei I also feel my rev cut comes too early.. Like ard 6.8k cut d.. Two days back at night I raced with putra straight pipe also.. Ahaha we both the car sound dam 7 loud lol imba Wei xD.. Btw if I take out one bullet, increase rev cut I think I can tapau light modded 4g93s.. Cuz now also can go line to line together just that they can rev much longer.. Ahaha dam.. I wanna change to 4g92 mivec but no engine Lantai around with ecu and wiring.. Haha and if I don't go above 7.5k rev my block doesn't need any oil squirters right? Need more info from you guys..

---------- Post added at 02:46 PM ---------- 6 hour anti-bump limit - Previous post was at 02:44 PM ----------

If got block will kena tahan meh? haha gg too loud or what??

 

[ACQ2305]

afatt,last i saw hydraulic lifter selling,16pieces, almost rm800...oversize oil passage thingy..about the service change,tat not sure..not yet done it yet.touch wood..
Cal,no harness..so if buy also cant use till d seller can find d harness...which i believe is very hard to find...

 

[alvin24]

afatt,
If not mistaken... long ago I changed all 16 lifters of mine for RM80 per piece brand new. IF ACQ says RM800 for 16 pieces, it's cheap.

Calvin,
Actually using a mid-muffler is more beneficial than bullets. If that way, use 2 also tak aper... minimal power loss on mid mufflers... but of course, less noise-reduction from it as well lar. A lot of vtecs use 2 mid mufflers on their exhausts.
*In case you guys not sure what a mid muffler is... it's like installing an N1 muffler to the mid pipes. =)

mediocre,
Get a rechip done to remove your rec cut. Those aren't expensive... i think somewhere around 300 bux. I haven't done it before, so I'm not sure of the exact price... but if not mistaken it's around there. Fueling I prefer to run on emanage, because it's much more 'tuner friendly' than rechip.

 

[ACQ2305]

Happy New year guys n girls(wonder if there's any,hehe)...
Nobody around during New year??

 

[alvin24]

happy new year too ! =)

Me still around!

 

[ACQ2305]

Anybody using pro ride absorbers and springs?? need some feedback about suspension. my GAB Hi / Low is gone..no more play,and there's a knocking sound. Mechanic check,the inner shaft inside moves a lot. 3 out of 4... no wonder la now very harsh ride...on a tight budget now,thats why cant get myself another adjustables. Anybody uses Mines? HWL?

 

[calvin9683]

U cAn send ur GAB for repair ma....

 

[fstr]

buy new one better, nowdays adjustables are kinda cheap

 

[ACQ2305]

was thinking of sending for service,but the cost 2 send it back and forth,and the price of servicing, almost as new as getting a new set.Cheaper brand. But it is about the quality that im skeptical about.Mines, HWL...Sustec..sowana get some feedback if any of us are riding on them.

 

[alvin24]

What's your budget lah? HWL brand new 1.4k i think... I heard HWL performance is not bad =)

Oh... another thing... just curious... how many people here use RON 97?

 

[ACQ2305]

kinda like below 1k. Cause rear tyres also needs to be replaced..rm350 per piece..
was thinking of just make do with lowered abs n spring.. Pro ride. heard about this brand b4?
Im using R97.. :)

 

[calvin9683]

Bro ACQ... u sure u can live wif lowered sport springs??? Since u r so used to adjustables d...
Dun later spend on another set of adjustables after using sport lowering spring... End up spending more... U know wat i mean???

Bro Alvin... I'm oso runnin on ron97... But seldom drive my car d... Ron97 so expensive nowadays... Somemore "abang abang" seems quite hardworking recently... Heehee

 

[ACQ2305]

argghhh,..hehehee..yeap,i know what you mean. But my situation now,well,it does not permit me to get a new set of coilovers. Only can afford those normal abs n spring..Adjusted it a bit higher 2 days ago,and can see that the inner shaft has some rubbing marks. Kinda like worn off. And can feel the abs moving in and out.And also leaking. Duno if can just use it for the time being and safe up,but cant stand the ride 'comfort' now.hahahaha..too harsh already if compare to another friends GAB on his satria....

 

[calvin9683]

Perhaps u can ask around if there's anyone who can repair ur adjustables in ur area???
If not then ask arOund if hav frens dat hav stock abs to borrow for the time being???

 

[ACQ2305]

Doubt that there's any shops where i am that have the know how about servicing abs..Lack of facilities.Have asked around if any friends has stock abs n spring around,most already kong..hehehe...Did ask how much it cost 2 service GAB, rm150 per piece. X 4 = rm600..courier back and forth,around rm50 one way.?? not sure about that,but should be around there...Hrmmm....But kinda set on getting lowered springs and abs...target comfort now..will see how long i can stand using that.If got budget,another set of adjustables, hi / lo soft / hard..

 

[MiTec-i]

alvin, running on high cams need colder plugs? i'm runnin pon(dan)cams....272degree only...should be ok rite...and guys...any ideas how to stiffen the valve springs?93T valve spring is it harder?

 

[joseph_lim75]

Hi All Sifu,

Can someone point me a honest and good mechanics that service 4g91 engine plus experience in changing timing belts or overhaul.

I am very afraid of shops which lack of experience and causing more harm than good to my car. Does anyone has any preference with reasonable price of doing the above mentioned ?

 

[skylee834]

Bro,ACQ,i m using the proride absorber plus APM performax spring,
well the proride Abs is quite good and hard enough for me,
but can feel that the spring of APM not enough hard but sure u can feel comfort ...
but if use other spring sure will better..
i buying the Abs around RM600--,and spring Rm140,plus this that already can buy a new set cheap adjustable..