Subaru bumper

[lkeong88]

I have just gotten a subaru impreza ver 3 bumper installed but the workmanship is not good. Is there any place with experience that can install it properly?

 

[km_chew]

Paging for ScottWrx

 

[scottwrx]

yes yes... anything i can help? u facing problem below the signal part right?

 

[lkeong88]

Ya below the headlamp there got big gap can put finger through. Can sifu scott tell me how to solve it? The shop I went to said need to paint then he can fill it with something? Not sure what he was telling me

 

[AE101-Wong]

Ya below the headlamp there got big gap can put finger through. Can sifu scott tell me how to solve it? The shop I went to said need to paint then he can fill it with something? Not sure what he was telling me

u can try my workshop in menglembu ipoh...
since ur hometown is taipeng, u can go there and have a try..it's very good workmanship, but the price is abit high la..but confirm u can satisfy the result..

 

[20V Trumpeteer]

hehehe...another bro scott follower....you can ask anything regarding the subaru bumper to scott...very nice person...hei bro scott...long time no see?been very busy lately ka?

 

[scottwrx]

there are 3 ways to do it,

1. use hot air gun to push the bumper to fill the gap and reinforce with a small cable tie, u drill a small hole underneath the signal, and then drill another hole at the fender and tie them up

2. use screw to screw directly into the fender - not nice coz u cant remove the bumper without damaging the paint, but it is the easiest way to do it

3. ask fibre shop to modify another bracket along the below the signal area, and srew it into the fender.

but either way also, u need to make sure that the bumper should protrude out at the wheel arch area, coz subaru bumper is longer than seg bumper on both width and length ( side length) i will try to post more pics if i m available

http://i295.photobucket.com/albums/mm148/scotttsl/subarubumperfender.jpg

the picture taken when i was using the original seg bumper after an accident, it is to show how to solve the protruding bumper from the wheel arch,(yellow line is the original fender before adding the steel plate. u need to add another piece of steel and paint it, any paint shop know how to do, so the bumper wont look so ugly from the side, and dun cut the bumper coz it will affect the strength of the mounting to the fender.

---------- Post added at 05:31 AM ---------- 6 hour anti-bump limit - Previous post was at 05:30 AM ----------

hehehe...another bro scott follower....you can ask anything regarding the subaru bumper to scott...very nice person...hei bro scott...long time no see?been very busy lately ka?

hehe.. very busy lately, coz working + training + seminars + MBA studies... lots of things going on.. dats y become less active.. hehe...

 

[lkeong88]

Thanks scott for the guide. Currently the shop use your option number 2 but the result not so nice. Bro Ivan, may I know where is the shop?

Actually I was hoping for a shop in KL or Selangor because I am no longer in Taiping

 

[AE101-Wong]

Thanks scott for the guide. Currently the shop use your option number 2 but the result not so nice. Bro Ivan, may I know where is the shop?

Actually I was hoping for a shop in KL or Selangor because I am no longer in Taiping

the workshop in menglembu ipoh...u can give me a call when u wanna go there...

 

[miib14]

my car with the subaru bumper on...

 

[lkeong88]

I have managed to get it done up but I will post the pics later. In KT I have no internet

 

[foofis]

nice, just keep it clean with no badges, more unique.

 

[miib14]

thanks

 

[lkeong88]

Updates:

http://img529.imageshack.us/img529/5361/img6750q.th.jpg
http://img502.imageshack.us/img502/694/img6752.th.jpg
http://img98.imageshack.us/img98/4903/img6753.th.jpg
http://img840.imageshack.us/img840/9309/img6754r.th.jpg

 

[spwn]

anyone installed Ver6 bumper on an SEG '99 before?

 

[koled_se]

anybody try on toyota SE limited@AE92@AE90 before?