cipan_supercas

Who told you that MS is not reliable? When it comes to tuning, it's the tuner's responsibilities, not the hardware. I'm using it with no issues.
If you want a stock type rock solid idle when using air-cond, I think don't even dream of changing your stock ecu. Stock is still the best. Not even the most expensive aftermarket ecu can give you that kind of stability for idle with air-cond 'on' at idle. They are aimed for performance. But it can be done. Just don't compare to stock.
It's not a good idea for people like you to start changing parts or mods either. That will screw up things which are frustrating sometimes. Keep everything stock and you should be fine. Whatever it is, if you want to have more info on what I have in hands, gimme a call. We can always discuss.

     

kennethfong

cipan,

thanks for the reply, i know there's a big hole in front, but i've to get down stepping on it (no way back), MS is undeniably cheaper option, could u pls tell me who could tune this up for me?? could MS reuse all existing sensors except MAF? i've just changed my blow off, i love it despite a bit ricey, so guess that's no way back to stock, my karman vortex doesn't like the VTA blow off, so i'm planning to discard my whole maf converting into MAP or hotwire setup, that's my actual purpose, but of coz many options available just wanna get one with good idling + performance at the same time....

i've tried HKS EIDS n it's worse causing stalling when air cond kicks in at the point of VTA.....

     

cipan_supercas

I think it's not nice to hijack this thread for Microtech to elaborate other product. It's better to start a new thread on this.

Just a brief note, you can use Maft-pro, Maf-T, or numerous standalones available. However, the price of Maft-Pro are much expensive than MS. If you're looking for affordable standalone, than MS is the answer. If you're talking about power, then it's your hardware and tune no matter what you use be it chipping, Maf-T, standalone etc.

I can assemble, install and tune MS. You can order it yourself and have me perfectly assemble and test the product before even installing it in your car or I can help you order the unit. But you have to bear the cost and the 43% tax imposed by the customs. (Please consult before ordering and I'll recomend what's needed to run your GSR).


If you want to discuss further on this topic, please start a new one.

     

kennethfong

cipan,

okie dookie new thread starting now...

     

phat7

Kenneth mate, good to see you on here. thanks for the phone call too. With regards to powerfc i'll get back to you with vendors name. When are we going to meet up ?

     

kennethfong

yo dev,

haven't been seeing u since eerh 5 years back was it?? if i go down kay el will give ya a call dude.... i'm still deciding which one to get either power fc or megasquirt, if you could gimme the vendor's name that'll be great coz i may have a long list of questions to ask hehe....

     

tuner

hi boss how is the MICROTECH TRAINING in december ????:shades_smile: :shades_smile: :shades_smile: :shades_smile: :shades_smile: :shades_smile: :shades_smile: :shades_smile: :shades_smile: :shades_smile:

     

tuner

boss is the microtech training stall on in december???????????????????????

     

rpm2racing

Contact RX Engineering for training section.
www.microtechefi.com

     

georgett

RX engineering located in australia...?

     

ltl_ek

bro i gor one unit of microtech mt8 but dont have mapsensor....can u recommend and quote the price of new or used part of the map sensor asap.... thank you...

     

tuner

rpm2racing how is the training section in this november stall on ??

     

punktuichea

frenz...may i ask u a few question?
my car is honda accord sm4, izzit suitable for putting LT8 for my car? or wat ecu u recommend? wat is the difrrent between LT8 and LTX8?
can give me more info/webside about LT8 or any ecu u recommend me?
do u hav any 2nd ecu to sell? or how much for the new 1? and i wan all the kit for laptop and support software.how much it wil cost?
coz i juz started mod on my car...going to bolt on turbo.using kkk26 turbine.
thanks bro...

     

georgett

LT8 is no build in ignitor, LTX8 is build in ignitor, but LT8 can buy external X4 ignitor, the fire is stronger than LTX8.
www.microtechefi.com
Recommend LT10s + X4, the price is RM100 extra than LT8s + X4