ecupro

Oh.......Petro..Off Sh...ha..ha...ha
Pro-SE basically work like Megasquirt Ver.1, so, can NOT control mitsu ISC.
You have to add two big valves. One for cold start and one for air-cond.

Off cause, you can use Megasquirt Ver.2 which is a piggy pack pcb and mount on Megasquirt Ver.1 's microcontroller socket.
then, you can control the mitsu ISC, but, which is very costly.
Thats why, a lot of people only use Megasquirt Ver.1 which is consider very cheap.

     

sumimasen

gone too long eh,
which means,u also need to highlight that Microtech is consider cheap too since it can't control the ISC. but lots r using it.

p/s=how is ur so called software going?can't wait to see any similarity with other EMS.

     

ecupro

He..he..he....
Pro-SE,Ms-Extra or MS is DIY ecu, so consider cheap.
But, Haltech,Microtech,Motec and others ems, there are product from factory,so there are expensive.

About my software, i thing some one did post on this thread.Check it out.

     

ecupro

The software was post by Xbalance2002 on page 8 in this thread.

     

apexi3016

i've gone thru all the pages n i'm confused...

i have a question, mr.ecupro, did u fully develop ur ECU or u got the pcb drawings n stuff from the MegaSquirt website n reproduced it??

thanx in advance

     

ecupro

Hello apexi3016,

Protech I/ Protech II are fully develop by me, ecupro.Even the firmware, dos software and Window software.

For the Pro-SE, i got the schematic diagram from Megasquirt website.
From the schematic diagram, i modify the diagram which some of the electronic components are very difficult to find.Basically, i need the microcontroller schematic diagram only.
Then, combine the Protech-II and MsExtra, become Pro-SE.
As you can see, Protech I/Protech -II and Pro-SE almost look the same.

     

apexi3016

alright... how much will ur one cost? and how do u tune it, using wideband or narrow band??

i'm very interested with MS and since there another one besides MS right in our country, it'll be great..

is ur one an open source like MS by Bowling n Grippo??

thanx.

     

ecupro

Hello apexi3016,
Protech-I/Protech-II is Not open source. Just like Haltech, Motec,Hydra,AEM and others advance ecu. By the way Protech-I/Protech-II is Not a DIY Kit.You can tune it either one,i.e wideband or narrow band.Again, narrow band is more cheap and also for refence.Off cause, for better quality, you can use wide band and also costly.

Pro-SE is a open source from MsExtra. It is a R & D kit.You can use any tune software from MsExtra or MS or Megatune.

Note: When you have a question, please indicate Protech or Pro-SE.Thanks in advance.

     

flamefox850

already PM u but u didn't answer. is the PRO-SE already 'pass' ur RnD phase ? how much PRO-SE including installation+1st time tune ? can install in 3 cylinder engine with distributor ignition system?

     

ecupro

Hello flamefox850,
Sorry that i didn't reply to your answer.

Yes, Pro-SE already pass the R&D phase for 4 cylinder engine like 4G61T but Not support Mitsu ISC.( Just like others MS-I )

The Pro-SE have two channel output for injectors.That mean, injectors have to run on batch, two injectors for one chanel or one output and the other two injectors for another channel.( Just like others MS-I )

For the three cylinder engine, the three injectors have to batch together for one channel ( like Toyota, old 4AGE system ). I think MS call it odd engine and i didn't try on this configuration. Perhaps, Master MS, Cipan can help here.

Pro-SE is R&D Kit.

Anyway, nice website that you create.
Hope i can also have this kind of setup because i do not how to make one.

     

contreasjun27

hey ecupro, may i know which of ur ecu can be done for my 4g91 bolt on turbo?pro-se or pro-techII??? currently i'm using Greedy Emange piggyback tune by Mr. Cipan...hopefully to hear from u thank you...really interested though

     

ecupro

Hello contreasjun27,
Both should be no problem.
Just like i say, Pro-SE ( Just like MS-I or MsExtra ) did not support Mitsu ISC and it is R&D Kit.
You have to add two big valve for cold start and air cond.

Protech II can support Mitsu ISC.

You can ask Master MS, Mr. Cipan intall one MS-I for you for a try. I think Mr. Cipan should have plug and play socket or "Link", that will save him a lot of time.
Off cause, try run must give some CREDIT to the MS master, Mr.Cipan.

     

contreasjun27

yeah Mr.Cipan really do a great job of tuning the car for me...btw may i know what function is Pro-SE availabel?