Sidebar

Proton Gen 2 ecu wiring diagram/code

V

vale46

Junior Member
Senior Member
Jun 28, 2005
12
0
1,501
Kuching
Anybody know about this? I am planning to install Greddy Emanage or SAFC to my car since I've BOT my engine and I got complete wiring diagram of my car but I don't know whick one to pick up. This are the sensors I've found: knock sensor, o2 sensor, combine MAP/MAT sensor, camshaft angle sensor, crankshaft angle sensor, ignition system, throttle position sensor and all 4 injectors. I can't find RPM signal wire to the ECU. Fot those who know about it, please inform me. Thanks in advance.
 
C

campro5807

Jan 24, 2010
1
0
1,501
Kuala Lumpur
Hi , u can tap from crankshaft sensor +ve side for RPM. I was installed smt6 piggyback to my campro.

May u share your wiring diagram with me ? My email is [email protected]

My phone is 0132760845

Thanks

---------- Post added at 11:39 AM ---------- 6 hour anti-bump limit - Previous post was at 11:36 AM ----------

Stock FPR for campro is 3.5 bar. Look at fpr body . Written they.

Thanks
 
R

rowanromano

Active Member
Senior Member
Jul 21, 2006
30
2
1,508
pin out #59 vehicle speed signal
pin out #60 engine speed signal

hope this may help u... :biggrin:
 
M

mivec_0102

Junior Member
Senior Member
Apr 11, 2006
11
0
1,501
vale46 said:
Anybody know about this? I am planning to install Greddy Emanage or SAFC to my car since I've BOT my engine and I got complete wiring diagram of my car but I don't know whick one to pick up. This are the sensors I've found: knock sensor, o2 sensor, combine MAP/MAT sensor, camshaft angle sensor, crankshaft angle sensor, ignition system, throttle position sensor and all 4 injectors. I can't find RPM signal wire to the ECU. Fot those who know about it, please inform me. Thanks in advance.
Click to expand...
Hello can u tell me and show me with the o2 sensor in the ecu port and wire.i cannot found it.because i want to tap the o2 sensor reading.

hope can help me.
 
K

Kidd

Jul 22, 2010
3
0
501
Singapore
Hi where can i get the ecu diagram for siemens ecu for proton gen 2. Its urgent need to do troubleshooting. Pls pm me the diagram or email me thks.
 
D

diel8965

Jan 31, 2010
3
0
1,501
kangar
Please email me also the wiring diagram.

[email: egrgtem
@gmail.com[/email]

Thanks so much

---------- Post added at 10:31 AM ---------- 6 hour anti-bump limit - Previous post was at 10:26 AM ----------

Please email me also the wiring diagram.

My email: [email protected]

Thanks.
 
You must log in or register to reply here.
Similar threads   Forum
Driving a detuned EVO 3 engined Proton Perdana Forced Induction & Engine Management
*water temperature sensor voltage low* proton persona Forced Induction & Engine Management
help me..urgent.. Forced Induction & Engine Management
In need of Proton S4PH ECU wiring diagram/Pin assignment Forced Induction & Engine Management
need help from uk with proton gti conversion Forced Induction & Engine Management
Gen2 auto cruise conversion Forced Induction & Engine Management
3rd Gear Proton 4G63 Turbo Forced Induction & Engine Management
Proton 4G63T SOHC Forced Induction & Engine Management
Mitsubishi/Presumably Proton Check Engine Light Diagnostics Forced Induction & Engine Management
proton wira 1.5 efi ecu Forced Induction & Engine Management
  Similar Threads  
Driving a detuned EVO 3 engined Proton Perdana Forced Induction & Engine Management
*water temperature sensor voltage low* proton persona Forced Induction & Engine Management
help me..urgent.. Forced Induction & Engine Management
In need of Proton S4PH ECU wiring diagram/Pin assignment Forced Induction & Engine Management
need help from uk with proton gti conversion Forced Induction & Engine Management
Gen2 auto cruise conversion Forced Induction & Engine Management
3rd Gear Proton 4G63 Turbo Forced Induction & Engine Management
Proton 4G63T SOHC Forced Induction & Engine Management
Mitsubishi/Presumably Proton Check Engine Light Diagnostics Forced Induction & Engine Management
proton wira 1.5 efi ecu Forced Induction & Engine Management

The Marketplace Latest

Recent Posts

Random Post Every 5 Minutes

dokaugot
DIY - Install FICD
Ever experienced engine stall with air-conditioner on when you car slow down? What if its happen at the moment when you in a middle of U-turn? I bet your heart will pounding rapidly.

FICD is a little device that will help you with this problem. The concept is, this device will allow vaccum leak by allowing more air into intake manifold hence engine have enough air and wont stall. Its also stabilize idle and drive will feel a little bit lighter with a/c on. For the one who familiar with...
Ask a question, start a discussion or post something for sale!
Post thread

Online now

Total: 817 (members: 0, guests: 817)

Enjoying Zerotohundred?

Log-in for an ad-less experience