Ivan's AE101 Build Thread 4AGE BT 20V6Spd No 56K

[JDM-EK-AE101]

Hey, just received your reply. Am not sure about the sensor for transmission maybe i can find out when i am more available.

But didn't you ordered Fujitsubo Giken header? those are oem installed.

No problem mate No rush...


No I still have the Stock from the Engine Swap at this moment. Looking for the HKS 4-4-1.

 

[JDM-EK-AE101]

New Gas Tank And Seals 2-26-14

 

[KenDiriwan]

There is a concern with HKS 4-4-1, if you internal isn't strong enough to output power. You will suffer power loss due to a way larger diameter of the header than any other aftermarket one. Also it compatible issue if you plan to install Cusco 4point lower brace

 

[JDM-EK-AE101]

There is a concern with HKS 4-4-1, if you internal isn't strong enough to output power. You will suffer power loss due to a way larger diameter of the header than any other aftermarket one. Also it compatible issue if you plan to install Cusco 4point lower brace

ohhh

I see...

wich models are the other good options for me?

 

[JDM-EK-AE101]

Gas Tank Coating 2-27-14


As It come...

Start applying the Coating...

Coated with rust inhibitor paint and Ready...

Lines and seals Installed...

 

[vr2turbo]

Even your tank so nice, too bad is hidden......lol

 

[KenDiriwan]

ohhh

I see...

wich models are the other good options for me?

Depends on the planned performance. If internal remain stock, the 4-2-1 from Fujitsubo, Cusco quite sufficient. Anyway stock header has the best low range rpm torque.

No problem if wana stick with HKS, just go for high deg cams, forged rod and 82mm piston lol

 

[JDM-EK-AE101]

Even your tank so nice, too bad is hidden......lol

hahaha yeahhh at least you seen it, I'm happy with that LOL

 

[JDM-EK-AE101]

Depends on the planned performance. If internal remain stock, the 4-2-1 from Fujitsubo, Cusco quite sufficient. Anyway stock header has the best low range rpm torque.

No problem if wana stick with HKS, just go for high deg cams, forged rod and 82mm piston lol

I saw 2 diferent models from Fujitsubo correct?

I have TODA Cam Gears, TODA Time Belt and Looking for (Tomei Pon Cams or Kelford Type A) Cams with Velocity Stacks.

 

[JDM-EK-AE101]

Gas Tank Exhaust HeatShield Installed 2-28-14


Installing the new Gas/Fuel Tank...

Gas/Fuel tank Installed and Exhaust Heat Shield Back in place...

 

[KenDiriwan]

I saw 2 diferent models from Fujitsubo correct?

I have TODA Cam Gears, TODA Time Belt and Looking for (Tomei Pon Cams or Kelford Type A) Cams with Velocity Stacks.

The only model i know off is this
https://www.fujitsubo.co.jp/prods/detail/000000000000001295/00000000000000002851/00000197

Which i am using.

Those i afraid aren't suffice to output the potential of HKS 441. It is labeled R.O (Race Only) liked Buddy Club Spec 2. Well it will be reveal once you go to the dyno

 

[JDM-EK-AE101]

The only model i know off is this
https://www.fujitsubo.co.jp/prods/detail/000000000000001295/00000000000000002851/00000197

Which i am using.

Those i afraid aren't suffice to output the potential of HKS 441. It is labeled R.O (Race Only) liked Buddy Club Spec 2. Well it will be reveal once you go to the dyno

This one correct?
http://www.rhdjapan.com/fujitsubo-super-ex-header-exhaust-manifold-ae101-ae111-ae111g.html

 

[KenDiriwan]

That's the one, similar part number.

 

[JDM-EK-AE101]

I'll be looking for one of those...

Actually don't see often the R-SR, Apexi, Cusco Right? Only The HKS & FGK?

 

[JDM-EK-AE101]

SS Braided Brake Lines 3-9-14


Stainless Steel Front Brake Lines

Installed