Oxygen voltage high

  • Updates: New Bump Button / Bigger Fonts / Thread Thumbnails added to all forum channels / Explore Similar Threads after reading any post / Dark Mode selectable via header lightbulb / Bigger text / Navigation bar Updated / Try Dark Mode - Select Light / Dark from the footer area / Hi All, the forums have just been upgraded, please bear with us while it is being improved as we speak - May 19 2020 0000hrs (Post your feedback here: FAQ Help)

Hazrin5l5n7

New Member

Hazrin5l5n7

New Member
May 22, 2020
6
0
1
29
Hi All,

Can i have a solution to my satria neo cps which have problem with the oxygen sensor shows voltage high on diagnostic test. I already reset my ecu. But the problem is repeating

I just installed 421 extractor where the oxygen sensor is placed below of car not at top.

I use works drop in air filter

Please help.
 

brokenjars

5 Year | Silver

brokenjars

5 Year | Silver
Jun 7, 2012
160
10
518
Kedah
Most probably there are leaks when installing the new extractor, or the oxygen sensor spoilt due to poor handling when installing the new extractor. Dont think is your ecu problem
 

vr2turbo

15 Year | Platinum
Helmet Clan
Moderator

vr2turbo

15 Year | Platinum
Helmet Clan
Moderator
May 11, 2010
29,247
8,169
1,713
Petaling Jaya
Hi All,

Can i have a solution to my satria neo cps which have problem with the oxygen sensor shows voltage high on diagnostic test. I already reset my ecu. But the problem is repeating

I just installed 421 extractor where the oxygen sensor is placed below of car not at top.

I use works drop in air filter

Please help.
If you can borrow an O2 sensor to test will be good.......
 

vr2turbo

15 Year | Platinum
Helmet Clan
Moderator

vr2turbo

15 Year | Platinum
Helmet Clan
Moderator
May 11, 2010
29,247
8,169
1,713
Petaling Jaya
Hi, i already replace the 02 sensor but problem still occur. This is the error code p0131, 0132, p0172
Usually only one error code, but yours have 3. One is low voltage, one is high voltage , and one is rich air fuel ratio, this really have to trouble shoot....
 

Hazrin5l5n7

New Member

Hazrin5l5n7

New Member
May 22, 2020
6
0
1
29
Those error shows when i rev at 5 to 6 k rpm.. below than no engine light. Is is possible due to location of the sensor? Or maybe due to wire extension made by the wshop
 

Hazrin5l5n7

New Member

Hazrin5l5n7

New Member
May 22, 2020
6
0
1
29
Yes. Extend the wire by simply cut it and solder with other wire.. i'm suspect this issue might be due to this or different location of the oxygen sensor. Will try to locate the sensor back to previous position
 

vr2turbo

15 Year | Platinum
Helmet Clan
Moderator

vr2turbo

15 Year | Platinum
Helmet Clan
Moderator
May 11, 2010
29,247
8,169
1,713
Petaling Jaya
Yes. Extend the wire by simply cut it and solder with other wire.. i'm suspect this issue might be due to this or different location of the oxygen sensor. Will try to locate the sensor back to previous position
Was about to mention sensor location, since you had no problems before mod. Now you mention wiring can be affecting it too....
 

Hazrin5l5n7

New Member

Hazrin5l5n7

New Member
May 22, 2020
6
0
1
29
Hi All, just managed to figure out what is really happening. Last pomen didn't connect the wire correctly and create wrong connection. Now everything back to normal. Thanks all
 

vr2turbo

15 Year | Platinum
Helmet Clan
Moderator

vr2turbo

15 Year | Platinum
Helmet Clan
Moderator
May 11, 2010
29,247
8,169
1,713
Petaling Jaya
Hi All, just managed to figure out what is really happening. Last pomen didn't connect the wire correctly and create wrong connection. Now everything back to normal. Thanks all
But how come previously running ok? Anyway, good to hear you got this issue settled.......