Haltech Platinum Series

lozo

500 RPM
Senior Member
Sep 26, 2004
897
7
5,018
Petaling Jaya
Visit site
yeup correct. why there is different...hmm sorry couldn't figure out. maybe to compensate the injectors delay. will do research on it
 

ftzone

full throttle zone
Senior Member
Feb 21, 2005
5,339
141
3,163
Penang, Prai
www.ftzoneracing.com
hehe... i have played a tiny bit with the injectors timing delay... the air fuel ratio will show a temporary rich condition before going full lean "due to decel cut" after letting off the throttle. Is that a good thing to do? If not mistaken that shouldn't be it rite? carbon deposit may build up over time and yet i assume the additional fuel before decel cut is good for cooling down the cylinders... unfortunately no loud popping sound between gear shifts...
 

lozo

500 RPM
Senior Member
Sep 26, 2004
897
7
5,018
Petaling Jaya
Visit site
i don't think there will be any carbon build up due to temporarily rich condition. at least it assist cooling though
 

Syahz

Known Member
Senior Member
Thread starter
Aug 14, 2009
484
21
1,518
Australia
How fast you can tune on the dyno?Short time,reliable and Quality.
Using the Haltech Duel Channel Wide Band and put your AFR target...run it.
You can run on the road or on the dyno if you have a facility your place.
Do profesional tuning on your self.Every time Innovative.
 

Attachments

Syahz

Known Member
Senior Member
Thread starter
Aug 14, 2009
484
21
1,518
Australia
Good News For RX7 and RX8 Club.

The Platinum Sprint RE

Engine Suitability:

• 2 Rotor Engines - 2nd Generation RX7 (FC3S)/Turbo II, 3rd Generation RX7 (FD3S) and RX8 (SE3P)

• Normally Aspirated or forced induction

• Load sensing by throttle position or manifold pressure (MAP)

• Sequential Injection

• Distributor ignition systems or multi-coil systems


Trigger Types:

• Reluctor


Trigger Patterns:

• Mazda Rotary Multitooth 24 and 2

• Mazda Rotary RX8

Pls Contact Your Haltech Dealer for more Information
 

Syahz

Known Member
Senior Member
Thread starter
Aug 14, 2009
484
21
1,518
Australia
Good News
For all waja engine and campro cps or non cps can running perfect with Sprint 500.
Pls contact your Haltech Certified Tuner.
 

Syahz

Known Member
Senior Member
Thread starter
Aug 14, 2009
484
21
1,518
Australia
Platinum sprint 500 on Toyota Lexus 6cylinder VVT

Official Haltech Forums • View topic - Lexus IS300 Turbo Sprint 500 ecu

---------- Post added at 11:01 AM ---------- 6 hour anti-bump limit - Previous post was at 10:49 AM ----------

VR6 running Haltech E8 semi-sequential.(6cylinder)No dramas.Can use for Perdana V6 turbo.
VR6 engine Je Pistons, Eagle rods, T3 60-1 Turbo Haltech E8 semisequential injection wasted spark ignition on stock coil pack
373WHP@ 1Bar boost

YouTube- Corrado VR6T 0-260 km/h
 

Airmund

Junior Member
Senior Member
Mar 10, 2009
14
3
1,503
Hey Syahz, PMed you regarding kelisa and haltech Sprint 500. ANyone here knows if Kelisa 2nd generation can tune ignition timing with Haltech 500? Coz i heard cannot tune with Emanage since using cam sensor.

ALso, will the Haltech 500 work with 3 cylinder supercharged Kelisa? Thanks for any help.

Cheers,
Ed
 

Syahz

Known Member
Senior Member
Thread starter
Aug 14, 2009
484
21
1,518
Australia
Hey Syahz, PMed you regarding kelisa and haltech Sprint 500. ANyone here knows if Kelisa 2nd generation can tune ignition timing with Haltech 500? Coz i heard cannot tune with Emanage since using cam sensor.

ALso, will the Haltech 500 work with 3 cylinder supercharged Kelisa? Thanks for any help.

Cheers,
Ed
No worries for kelisa 3cylinders.we know the trigger type and set up.May be u can ask the haltech Tech for the clear message.Or u can ask your nearest dealer.
 
Last edited:

Syahz

Known Member
Senior Member
Thread starter
Aug 14, 2009
484
21
1,518
Australia
350Z already use Pro Platinum plug in.And more function for tuning.
You can refer with super duper dealer Haltech or Haltech Certified Tuner.
 
Last edited:

Random Post Every 5 Minutes

hi all, got this problem after transplant to 6a12TT. My car now like not enough voltage, everytime I open door, my alarm system auto switch on hazard light (both signal lamp blinking)..when that happen, all inside-car lamp,clock,warning light keep fade in-fade out following that hazard light.According Volt meter in my Apexi TT,reading are 13.5-14.0 with engine idling. And when I keep pressing my auto window..voltage drop 1 by 1 till 13.0...I got pivot raisin VS installed but no G-cable as my...
Ask a question, start a discussion or post something for sale!
Post thread

Online now

Enjoying Zerotohundred?

Log-in for an ad-less experience