4AGE 20V Engine bay pics

[cruiser78]

I think this type of engine mounting is the best for your EE90. Coz I'm driving an EE90 too with BT and i'm using this type of mounting. Easiest to modify, less problem and no Q&A session with the Puspakom guys

Most engine, brakes and suspension parts from AE111 can be retrofitted EE90. Some just plug and play (swap without any modification) My AE92 is using AE111 twinpot front brakes, AE111 rear brakes, AE101 suspensions (springs and absorbers), driveshafts, steering rack. Some of the part number are the same from AE90 thru AE111 such as front spring, rear disk pad, etc

But you cannot put AE111 seat into EE90 without modifications because the seat mountings of our AE92 is are different from AE111. You can get a complete AE92 front and rear seat. If you are lucky enough, you can get a complete AE92 GT APEX seat.... But much more expensive than AE111 Good luck with your conversion...

 

[vh-101]

My engine bay 4AGE 20v Turbo managed by Haltech.

Thanks.

 

[zmays]

ur radiator so cute..

 

[kungkung]

any pict ???

 

[jack84]

My engine bay 4AGE 20v Turbo managed by Haltech.

Thanks.

Very nice ! !

 

[vh-101]

Very nice ! !

thanks.

 

[six060six]

hi all... i wanna buy nology hotwires(red) anybody have it and wanna sell it? please pm to me.. Thanks...

 

[olskool]

hi all... i wanna buy nology hotwires(red) anybody have it and wanna sell it? please pm to me.. Thanks...

Paging for Ivan! Paging for Ivan!

Try ask AE101-Wong bro..he has brand new ones..:stupid:

 

[AE101-Wong]

Paging for Ivan! Paging for Ivan!

Try ask AE101-Wong bro..he has brand new ones..:stupid:

lol...i don have brand new lar...
i only have used 1...
brand new is hotinazma without grounding cable...
thicker than ultra, never use b4...

 

[dreamsquall]

My engine bay 4AGE 20v Turbo managed by Haltech.

Thanks.

may i know wat is the cloth covering ur piping system and where i could get it commonly?

 

[six060six]

hehe.. ok thanks....

i also looking for below part :

fgk extractor 4-2-1../hks extractor 4-2-1
ae111 gt nosecut with foglight..
ogura clutch set with bearing..
toms/imec trumpet..
TRD antirollbar frontSS and rear

but i cannot buy all laaa.. just asking for the price and wanna know if yall have the item. hehe

thanks...

---------- Post added at 06:56 AM ---------- 6 hour anti-bump limit - Previous post was at 06:41 AM ----------

My engine bay 4AGE 20v Turbo managed by Haltech.

Thanks.

bro..

did puspakom/jpj approved your bt turbo?

 

[vh-101]

may i know wat is the cloth covering ur piping system and where i could get it commonly?

Do you mean the thermal wrap? If that is what you mean, you can get it from any performance shops in KL..

you just told them you need thermal wrap..

 

[BDK8671]

My engine bay 4AGE 20v Turbo managed by Haltech.

Thanks.

nice bolt on .....bro ....

> 200ps ?. ....

 

[vh-101]

nice bolt on .....bro ....

> 200ps ?. ....

thank you. yes 300 on wheel.

 

[pcmoddingmy]

thank you. yes 300 on wheel.

Fuuuhhh.... 300ps shouldn't be bolt on, I bet your internals had been fully beefed up as well. Care to share more pics and specs as well?