RPM controlled switching- Launch/NOs/Mivec?sub injector/etc

[E-Tech]

Hi guys...

If used as launch function (rev cut)...
Some of you like the concept because sounds nice at traffic lights or stops,
where you can full throttle and pa pa pa pa pa pa pa pa....

Another option for those with hondas ... P08/P30 ecu
Below is a chip for std B16A use which include these....beside fuel/ign up...
Vtec- 5600
Rev cut- 8800
Launch- 4500
S/light 8000
No Speed cut..

 

[ashez]

bro etech....me wanna diy actually....
btw thankz alot...will be waitin 4 u..

 

[E-Tech]

bro etech....me wanna diy actually....
btw thankz alot...will be waitin 4 u..

Bro,
I will mail you the excel file 2morrow okay....
BTW you already receive the components for boost cut overide?
And another thing.... u suppose to send me the picture of L5 ecu...already?

Tq

 

[ftzone]

uwah lao eh... very nice end product with presentable casing as well.. during my college days i did some of these kind of electronics but all that knowledge i pass back to my teacher already... forget everything already. damn... i salute u la e-tech... because your total packaging is good... the sticker also make... fuh.

but the rev-limiter consistant or not? hehehee.

 

[E-Tech]

uwah lao eh... very nice end product with presentable casing as well.. during my college days i did some of these kind of electronics but all that knowledge i pass back to my teacher already... forget everything already. damn... i salute u la e-tech... because your total packaging is good... the sticker also make... fuh.

but the rev-limiter consistant or not? hehehee.

Tq...
Consistansy...Can-lah....
Oledi tested at Sepang (SDB) then i guess quite good cheap diy...
Started to make this also because of the low budget drag car...
If 2morrow not too busy, i post the prototype picture for you...the casing use strepsils paper box...

 

[ashez]

bro..havent recive the stuff yet....
the email u sent me no attachment...
i will give u my other email later u email it to me there....

 

[E-Tech]

bro..havent recive the stuff yet....
the email u sent me no attachment...
i will give u my other email later u email it to me there....

bRO..
yAHOO changed their mail format...
already resend to u guys... if cannot see still let me
know... i put link to my bucket of photos...

 

[4G93NAPower]

I do have 1 or 2 laying around...
Do let me know what you intent to use if for...
In addition, you would basically need a std automotive 12V relay..
TQ

hmm basically just launch control, need that for my car

got any demo video?

 

[E-Tech]

hmm basically just launch control, need that for my car

got any demo video?

Will try to get frm a recently installation on Satria 1.5....
and post it.....might need some assistant in this area....Tq

 

[nan83]

for launch control you off the ignition?? huhuhu... that so rough rev cut setup.... scare bearing kong laaa... normally launch control just retard the timing.... not turn off the ignition...

just my opinion ...

 

[E-Tech]

bRO....
I understand your concern but maybe you mis-understand
"Ignition" here is meant as the spark ignition...
Not the kunci ignition....
Tq

 

[nan83]

hahahaha... i know lah... not the kunci ....

you maybe put relay on the +ve wire to the coil right .... the shiflamp rpm output to control the relay right??? so you just set the rpm setpoint, the relay will break the circuit when it touch the rpm... so you will cut power to the coil... is that right??

 

[E-Tech]

That 's basic idea plus resistors.(like MSD)- org kelate kata resistoR batuuuuu
Btw pls teach us which bearing are you taking about? Nanti salah paham lagi...
Pls advise .. thanks...

 

[nan83]

owh.... with resistor ..... so the spark still there while relay energize ?? just weak spark??

can share with me your circuit diagram??? ehehhehe..


conrod bearing lah ... i tot you just shut off coil power at hi rpm for that... hi rpm + coil power on than off than on than off.... sakit jugak kalau camtu....

if haltech launch control.... can set soft cut.... it will retard ign timing + fuel enrichment to ensure engine to take to much abused...

 

[E-Tech]

Me share wit you... shylah...
you expert class..main turbo dgn stand alone ecu ,dyno tuned lagi and plus butt road tuned....
Maluuuuuuuuuuuuu lah I...:vroam:
Anyway thanks for your concerns and contribution...PEACE.

Bro btw... haltech E6X problem of launch control already debugged kah?
Quote...."actually there is some bug on E6X to run this launch control function ... for more detail ... contact Haltech dealer or Haltech Aus ... if you dun mind ... can ....
Tq